Innowireless Co., Ltd.

Joo Hyeong Lee

Jin Soup Joung

Yong Hoon Lim

Kyoung Hwan Ju

Byung Kwan Jang

Provided is a channel simulator having a function of supporting a carrier aggregation and a carrier aggregation block used for the same to support a carrier aggregation function at a minimum path loss without reducing the number of valid connectable terminals. The channel simulator includes: a terminal interface block connected to each of at least four terminals through at least two transmission/reception ports; a carrier aggregation block including unit modules each including one RF coupler and one RF switch, and interposed between the terminal interface block and the terminal to support the carrier aggregation for one to four component carriers; and a management server. The carrier aggregation block includes a front-end carrier aggregation unit and a rear-end carrier aggregation unit.

Channel simulator having function of supporting carrier aggregation and carrier aggregation block used for the same

Provided is a control method for a channel simulator, capable of expanding a processable dynamic range of an uplink signal receiving unit while adopting an A/D converter (ADC) having low resolution by adjusting an attenuation amount of the uplink signal receiving unit in a large-capacity channel simulator having P base stations and Q terminal interfaces. In a control method for a channel simulator that includes P base station interface cards (BS I/F cards) (P&#x3e;2; P is an integer), a link processor block, and Q user equipment interface cards (UE I/F cards) (Q&#x3e;2; Q is an integer) to form channels with respect to all paths between P base stations and Q terminals, the control method for the channel simulator according to the present invention includes: (a) establishing a table representing an attenuation amount offset in an uplink signal receiving unit of the UE I/F card over a path loss based on log data with respect to terminal transmission power over the path loss for eliminating change of the path loss exerting an influence upon the terminal transmission power; (b) searching for a specified path loss value from the table established in step (a) to determine an attenuation amount corresponding to the specified path loss value when a path loss value with respect to an uplink signal processing process is specified; and (c) adjusting an attenuation amount in the uplink signal receiving unit of the UE I/F card based on the attenuation amount determined in step (b).

Channel simulator using path loss of terminal transmit power to establish attenuation amount in uplink signal to base station

Provided is a method of calibrating a power for a multiple input and multiple output-orthogonal frequency division multiplexing transmitter having a plurality of antennas via a measurement equipment, the method including: receiving a cyclic delay diversity (CDD) signal simultaneously output from the transmitter to obtain a starting point of a frame of a corresponding signal; performing a fast Fourier transform on a sample proceeded from the starting point by an extent of a maximum CDD delay; calculating a channel coefficient; calculating a channel impulse response and a power of the channel impulse response; converting CDD delay values of each antenna into values in units of samples by using a sampling rate in the channel impulse response; mapping a peak point position of the channel impulse response to each antenna using CDD delay sample values; and simultaneously performing a power calibration of each antenna based on each peak point power.

Method of calibrating power for MIMO-OFDM transmitter

Provided is a method of processing a Wideband Code Division Multiple Access (WCDMA) signal timing offset for a signal analyzer. The method includes estimating an integer multiple timing offset of WCDMA baseband sample data corresponding to an amount of at least one frame; generating a frequency domain signal which is time delayed corresponding to a fractional timing offset estimation resolution after generating the frequency domain signal by performing a Fast Fourier Transform (FFT) calculation on an already-known reference signal; converting each time-delayed frequency domain signal into a time domain signal by performing an Inverse Fast Fourier Transform (IFFT) calculation on each time-delayed frequency domain signal and calculating a correlation between an input signal from a position of the integer multiple timing offset and the time domain signal; and estimating a delay time leading to a maximum correlation as a fractional timing offset.

Method of processing WCDMA signal timing offset for signal analyzing equipment

Provided is a method of blindly estimating WCDMA OVSF of a signal analyzer, which includes: (a) setting SF to 512 and an index thereof to 0; (b) calculating a power average value of a symbol obtained by despreading descrambled data with an OVSF code set by increasing the index from '0' by '1'; (c) determining an OVSF code by which the power average value is equal to or greater than a power reference value as a used OVSF code candidate and determining an OVSF code by which the power average value is less than the power reference value as an unused OVSF code; (d) comparing a zero crossing rate of a symbol with a reference value to determine whether the OVSF code candidate is the used OVSF code; and (e) repeating (b) to (d) while reducing the SF half by half until the SF is equal to 4.

Growing community of inventors

Seoul, South Korea

Joo Hyeong Lee