University of Central Florida Research Foundation Inc

John Sherwin

Bart Dean Hibbs

Danny S Parker

Devices, apparatus, systems and methods of attaching storm panels over window and door openings with end fastenable H tracks. Each of the tracks can have H cross-sectional shapes with elongated opposite facing C shaped channels back to back along the elongated tracks. At the upper and lower ends of the tracks can be outwardly protruding tabs having through-holes for allowing the tracks to mounted into frame edges about the window and door openings. Rectangular shutter panels such as plywood, metal and plastic sheeting can have side edges that slidably fit into the C channel openings of the H tracks so that the only fasteners to attach the panels over the building openings are through the track tabs. Stop flanges can prevent the panels from sliding out of the channels. The track, brackets can be mounted horizontal and parallel to one another as well as be mounted vertically and parallel to one another.

Channel tracks for attaching storm panels over openings on buildings

Conical diffusers with or without conical center bodies can improve air moving performance by up to 21% at no increase in power. Embodiments coupled with electronically commutated motors (ECMs) showed additional reductions to condenser fan power of approximately 25%. A strip member, such as open cell foam can be applied as a liner to the interior walls of a condenser housing adjacent to the wall surface where the rotating blades sweep against. The porous edge can also be used with the trailing edge and/or tip edge of the blades. These members can both improve air flow by reducing dead air spacing between the rotating blade tips and the interior walls of the condenser housing, as well as lower undesirable noise sound emissions.

High efficiency air conditioner condenser fan with performance enhancements

Novel twisted blades with an air foil for use with air conditioner condensers and heat pumps that provide improved airflow efficiency to minimize operating power requirements having an overall diameter across the blades being approximately 19 inches, and approximately 27.6 inches. The blades (AC-A) can run at approximately 840 rpm to produce approximately 2200 cfm of air flow using approximately 110 Watts of power from an 8-pole motor. Using an OEM 6-pole &#x215b; hp motor produced approximately 2800 cfm with approximately 144 Watts of power while running the blades at approximately 1100 rpm. Power savings were 25% (50 W) over the conventional configuration. A second version of the fan (AC-B) with some refinements to the flow geometry produced a similar air flow while using only 131 W of power at 1100 rpm. Power savings were 32% (62 W) over the conventional configuration. Embodiments can include two, three, four and five blades equally spaced apart from one another about hubs. Additionally, a novel noise reduction configuration can include asymmetrically mounted blades such as five blades asymmetrically mounted about the hub. Short, conical diffusers were shown to further improve air moving performance by up to 18% at no increase in power. Embodiments coupled with electronically commutated motors (ECMs) showed additional reductions to condenser fan power of approximately 20%.

High efficiency air conditioner condenser fan

High efficiency air conditioner condenser twisted fan blades and hub

Twisted blades for outdoor air conditioner condensers and heat pumps that improve airflow efficiency to minimize operating power requirements. The blades can run at approximately 850 rpm to produce approximately 1930 cfm of air flow using approximately 110 Watts of power from an 8-pole motor with an improved diffuser assembly. Using an OEM 6-pole &#x215b; hp motor produced approximately 2610 cfm with approximately 145 Watts of power while running the blades at approximately 1100 rpm. Power savings were approximately 24% (40 to 50 Watts) over the conventional configuration with increased air flow. Embodiments of two, three, four and five blades can be equally spaced apart from one another about hubs. Additionally, a novel noise reduction configuration can include asymmetrically mounted blades such as five blades asymmetrically mounted about the hub. Additional features can include conical diffusers with or without conical center bodies were shown to further improve air moving performance by up to 21% at no increase in power. Embodiments coupled with electronically commutated motors (ECMs) showed additional reductions to condenser fan power of approximately 25%. A strip member, such as open cell foam can be applied as a liner to the interior walls of a condenser housing adjacent to the wall surface where the rotating blades sweep against. The porous edge can also be used with the trailing edge and/or tip edge of the blades. These member can both improve air flow by reducing dead air spacing between the rotating blade tips and the interior walls of the condenser housing, as well as lower undesirable noise sound emissions.

Growing community of inventors

Cocoa Beach, FL, United States of America

John Sherwin