Nova Chemicals Inc.

Metromont Corporation

Syntheon, LLC

Michael T. Williams

John K. Madish

Jay Bowman

Roger Moore

Tricia Guevara

David A. Cowan

Kolapo Adewale

John K Madish

Michael T Williams

David Allen Cowan

Mary Margaret Moore, Legal Representative

Rick Hughes

Michael R Kelley

Tobias Blain Hileman

Kristen Van Buskirk

Tricia Ladely (Guevara)

Jay J Bowman

Blain Hileman

Kristen VanBuskirk

Tricia Guevara Ladely

Daniel Woolfsmith

Richard H Pennell, Jr

Richard H Pennell

Roger (deceased) Moore

Trica Guevara

Roger Morre

David A Cowan

A lightweight ready-mix concrete composition that contains 8-20 volume percent cement, 11-50 volume percent sand, 10-31 volume percent prepuff particles, 9-40 volume percent coarse aggregate, and 10-22 volume percent water, where the sum of components used does not exceed 100 volume percent;. The prepuff particles have an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.02 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3. The slump value of the composition measured according to ASTM C 143 is from 2 to 8 inches. After the lightweight ready-mix concrete composition is set for 28 days, it has a compressive strength of at least 1400 psi as tested according to ASTM C39.

Lightweight concrete compositions

A lightweight concrete composition containing from 10 to 90 volume percent of a cement composition, from 10 to 90 volume percent of particles having an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.03 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3, and from 0 to 50 volume percent of aggregate; where the sum of components used does not exceed 100 volume percent, and where after the lightweight concrete composition is set it has a compressive strength of at least 1700 psi as tested according to ASTM C39 after seven days. The concrete composition can be used to make concrete masonry units, construction panels, road beds and other articles.

A method of placing a concrete compositions including a) combining 3-40 volume percent cement, 5-50 volume percent fine aggregate, 5-50 volume percent coarse aggregate, and 10-22 volume percent water; b) adding 1.5-40 volume percent of prepuff particles to form a concrete composition; and c) pumping the concrete composition to a point higher in elevation than the delivery point of the concrete to place the concrete. The concrete composition contains less than 30 volume percent of other light weighting aggregates and the prepuff particles have an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.02 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3. The slump value of the placed concrete measured according to ASTM C 143 is greater than 1 inch and the concrete has a density of from about 40 to about 135 lb./ft.

Method of placing concrete

A lightweight cementitious composition containing from 22 to 90 volume percent of a cement composition and from 10 to 78 volume percent of particles having an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.03 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3, where after the lightweight cementitious composition is set it has a compressive strength of at least 1700 psi as tested according to ASTM C39. The cementitious composition can be used to make concrete masonry units, construction panels, road beds and other articles and can be included as a layer on wall panels and floor panels and can be used in insulated concrete forms. Aspects of the lightweight cementitious composition can be used to make lightweight structural units.

Lightweight compositions and articles containing such

A lightweight cementitious composition containing from 10 to 90 volume percent of a cement composition, from 10 to 90 volume percent of particles having an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.03 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3, and from 10 to 50 volume percent of sand and/or other fine aggregate, where at least a portion of the sand and/or fine aggregate has a fineness modulus of less than 2; where the sum of components used does not exceed 100 volume percent, and where after the lightweight cementitious composition is set it has a compressive strength of at least 1700 psi as tested according to ASTM C39 after seven days. The cementitious composition can be used to make concrete masonry units, construction panels, road beds and other articles.

A lightweight ready-mix concrete composition that contains 8-20 volume percent cement, 11-50 volume percent sand, 10-31 volume percent prepuff particles, 9-40 volume percent coarse aggregate, and 10-22 volume percent water, where the sum of components used does not exceed 100 volume percent. The prepuff particles have an average particle diameter of from 0.2 mm to 8 mm, a bulk density of from 0.02 g/cc to 0.64 g/cc, an aspect ratio of from 1 to 3. The slump value of the composition measured according to ASTM C 143 is from 2 to 8 inches. After the lightweight ready-mix concrete composition is set for 28 days, it has a compressive strength of at least 1400 psi as tested according to ASTM C39.

Growing community of inventors

Negley, OH, United States of America

John K Madish