Gm Global Technolgoy Operations, Inc.

John A Hibner

Carl A Lentz

Jeffrey Kurt Runde

Joseph H Hunter

Christopher R Wiles

Jon M Huber

Michael R Ludzack

Shailendra K Parihar

In an automatic transmission, clutch-to-clutch closed throttle downshifting is controlled by filling the on-coming clutch at a maximum pressure command for a set period while commanding the off-going clutch pressure to a low value and exhausting the off-going clutch before the end of the fill period. At the end of the fill period the on-coming pressure is set to an initial value and then ramped up until turbine speed is pulled up due to off-going clutch slippage. Then a closed-loop profile control period starts wherein the slip of the on-coming clutch is measured and controlled to a slip profile. When synchronization of the on-coming clutch is detected, maximum pressure is commanded. Parameters for controlling the quality of a shift such as on-coming clutch initial pressure and on-coming clutch fill time are automatically adjustable during vehicle use to correct shift aberrations which degrade shift quality.

Method of adaptive control for closed throttle downshift in an automatic

In an automatic transmission, upshifting is controlled by ramping down the pressure in an off-going clutch associated with a high speed ratio and increasing the pressure in an on-coming clutch associated with a lower speed ratio. The on-coming clutch has commanded pressure at a maximum value for an initial fill time, a lower increasing ramp value during the ramp of the off-going clutch until the on-coming clutch starts to engage, and then a closed-loop control until the clutch reaches a synchronous speed. The closed-loop control parameter is on-coming clutch slip speed which is controlled to a calculated slip speed profile. The profile has a first steep slope and a final less steep slope so that the actual slip can smoothly go to zero in a given time period.

Clutch-to-clutch control in an automatic transmission

Garage shifts are accomplished at shifts from neutral to forward or reverse or between forward and reverse. An off-going clutch is released at the beginning of the shift for shifts between forward and reverse; shifts from neutral have no off-going clutch. The on-coming clutch has a fill time at maximum pressure, a lower increasing pressure ramp to begin engagement as indicated by pullup or pulldown, and a closed-loop control triggered by pullup or pulldown. The closed-loop control commands the pressure to control the turbine speed to a calculated profile to bring the speed to a target value. When the target value is attained the closed-loop control is terminated and maximum pressure is applied. For low speed shifts and for a high speed shift between forward and reverse, the target value is zero. For high speed shifts from neutral the target value may be either above or below the initial turbine speed.

Control method for automatic transmission garage shifts

In an automatic transmission, clutch-to-clutch closed throttle downshifting is controlled by filling the on-coming clutch at a maximum pressure command for a set period while commanding the off-going clutch pressure to a low value and exhausting the off-going clutch before the end of the fill period. At the end of the fill period the on-coming pressure is set to an initial value and then ramped up until turbine speed is pulled up due to off-going clutch slippage. Then a closed-loop profile control period starts wherein the slip of the on-coming clutch is measured and controlled to a slip profile. When synchronization of the on-coming clutch is detected, maximum pressure is commanded. If the throttle is opened during the downshift, the algorithm reverts to a powered downshift algorithm if the off-going clutch still has pressure or to an open-loop ramp control of the on-coming clutch if the off-going clutch has been exhausted.

Method of clutch-to-clutch closed throttle downshift in an automatic

The disengagement of the off-going clutch is monitored to determine as early as possible if there is a clutch tie-up due to failure to disengage. Beginning at the initial clutch release command, the turbine speed and output speed are used to determine if clutch slip has occurred and a pass signal is given if slip occurs in several consecutive control loops. Beginning a preset time after the command to fully exhaust the clutch, the number of no-slip conditions are counted. A fail signal is given when a set number of no-slip conditions are counted.

Growing community of inventors

Coldwater, OH, United States of America

John A Hibner