Hon Hai Precision Industry Co., Ltd.

Hong-Fu Jin Precision Industry (Shenzhen) Co., Ltd.

Huawei Technologies Co., Limited

Tencent Technology (Shenzhen) Company Limited

Honor Device Co., Ltd.

Nanning Fugui Precision Industrial Co., Ltd.

Hongqisheng Precision Electronics (Qinhuangdao) Co., Ltd.

Zhen Ding Technology Co., Ltd.

Fukui Precision Component (Shenzhen) Co., Ltd.

Shenzhen Alltokee Technology Co., Ltd

Shenzhen Aobin Technology Co., Ltd.

Dongguan Aobin Technology Co., Ltd.

Zte Corporation

Jian Luo

Hui Jin

Ming-Jaan Ho

Li Fan

Yi Ren

Xian-Qin Hu

Liuliu Ji

Fu-Shun Huang

Fu-Yun Shen

Yuanpeng Li

Hongyu Li

Zhenwei Zhang

Songping Yao

Yi-Hua Liu

Richard Stirling-Gallacher

Zhongfeng Li

Yingwei Li

Shu-Wei Zhou

Kuo-Jung Huang

Chun-Nan Ou

Yi Rui

Yi-Qiang Zhuang

Hongming Zhang

Liang Guo

Chia-Hsiang Ou

Minyi Huang

Mei Huang

Yi Qin

Yilin Li

Xuyang Du

Hong-Lian Huang

Guojian Zhai

Zhihang Li

Lanchao Zhang

Kaiming Dong

Pixian Yan

Lifen Bao

Changjian Yu

Qiang Huo

Li Fu

Guanglei Zhao

Outdoor fan

A negative pressure masturbator cup includes an accommodating cavity, a cup main body, and a control structure. The accommodating cavity is configured to accommodate a soft colloid. The cup main body has an elastically deformable body. The control structure has a negative pressure generator. When the control structure controls the negative pressure generator to generate a negative pressure, the soft colloid is pulled by the negative pressure generated by the negative pressure generator, and the elastically deformable body is deformed in a direction towards the accommodating cavity.

Negative pressure masturbator cup

A transmission line assembly includes a transmission line and a first filter. The transmission line is configured to transmit a radio frequency signal, and the transmission line has a first end and a second end. The transmission line includes an inner conductor and an outer conductor. The first filter is connected to one end of the outer conductor of the transmission line. The first end of the outer conductor is grounded through the filter.

Transmission line assembly, antenna assembly, and mobile terminal

A transmitting device and a receiving device for wireless communications are provided, particularly for vehicle-to-everything (V2X) or cooperative intelligent transport systems (C-ITS) communications. The transmitting device is configured to determine more than one transmission for transmitting a packet, and transmit the packet to a receiving device and/or a group of receiving devices using the determined transmissions. The receiving device is configured to receive a packet in more than one transmission from a transmitting device, and combine the transmissions to obtain the packet. Corresponding transmitting and receiving methods are also provided.

Transmitting device and receiving device for wireless communications

This application provides an antenna assembly. The antenna assembly includes at least a first antenna and a second antenna. The first antenna includes a first feed point and a first radiator connected thereto. The second antenna includes a second feed point and a second radiator connected thereto. There is a gap between the first radiator and the second radiator. An end of the second radiator close to the gap is provided with a first ground wire shared by the first antenna and the second antenna. An end of the second radiator away from the gap is provided with a second ground wire. Because currents excited by the first antenna and the second antenna are orthogonally complementary, crosstalk does not occur between the ground currents of the first antenna and the second antenna.

Antenna assembly and mobile terminal

A method for displaying a battle interface in a terminal is provided. The method includes: displaying a battle board in a user interface (UI) of a screen; obtaining an ilocation switching instruction; eliminating connected to-be-eliminated elements with a same type according to the ilocation switching instruction; displaying placeholder identifiers of lattices corresponding to the eliminated elements as a first placeholder identifier; and displaying a winner.

Method for displaying battle interface in terminal, device, and storage medium thereof

A push-button on a device includes a shell of the device, an internal locking portion to connect with the device, a touch pole far away from the locking portion, and a supporting flange portion extending from the internal surface of the shell. The supporting flange portion and the device support each other. When the shell is pressed, the push-button elastically deforms as the locking portionacts as a fixing point and the supporting end acts as a supporting point. The touch pole moves with the shell and the switch on a PCB is triggered to generate at least one signal.

Push-button structure and electronic device with the same

A flexible circuit board includes a first base layer, a circuit layer, a second base layer and a bonding layer. The circuit layer is coupled to a side of the first base layer and includes a linear signal line, two grounding lines located at two opposite sides of the linear signal line, and two hollow areas located between the linear signal line and the grounding lines. The bonding layer couples the second base layer to the circuit layer and defines a first opening corresponding to the linear signal line and communicating with the hollow areas of the circuit layer. The first opening of the bonding layer and the hollow areas of the circuit layer cooperatively define an air medium layer surrounding the linear signal line. A method for manufacturing the flexible circuit board is also provided.

Flexible circuit board and method for manufacturing same

A printed circuit board includes a mounting area. The mounting area includes a first mounting portion and a second mounting portion. The first and second mounting portions partially overlap. The first mounting portion includes a number of first holes, a number of second holes, and a third hole. The first holes, the second holes, and the third hole are configured for the mounting of signal pins of a universal serial bus (USB) pin. The second mounting portion includes the first holes and a number of fixing holes. The first holes are configured for the mounting of signal pins of a USB connector. The fixing holes are configured for the mounting of fixing pins of the USB connector.

Printed circuit board

A holding fixture includes a first part, a securing member and a second part. The first part includes a first end face and a sleeve extending from the first end face, the sleeve defines a plurality of radial through holes each receiving a ball therein, and each ball has a diameter larger than the wall thickness of the sleeve therein. The securing member located around the sleeve includes a plurality of protrusions configured on an inner wall thereof, with every two neighboring protrusions defining a notch therebetween. The second part includes a body and a tail fixed on the body, with seating thereof in the sleeve enabled by an annular groove in the periphery thereof. The protrusions guide the balls into the annular groove to secure the second part on the first part.

Holding fixture

A stamping die () includes a base set (), a punch () detachably assembled on the base set, and a stripper plate () disposed on top of the base set. The stripper plate defines a through hole () through which the punch passes, and at least one elastic member () is disposed between the base set and the stripper plate. The stamping die can punch different shaped holes by means of changing the punch.

Stamping die

A punching assembly includes a die base, a sleeve, an adjusting screw, a pull portion, a latching block, an elastic element, a fixing ring and a stop member. A top of the die base is received in the sleeve. The adjusting screw includes a contact end, a mounted end inserting into the sleeve and connecting to the top of the die base, and a latching portion located between the contact end and the mounted end. The pull portion is disposed around the sleeve. The latching block engages the latching portion. The elastic element is disposed around the adjusting screw, supporting the latching block. The fixing ring surrounding the adjusting screw is fixed on the sleeve. The stop member, contiguous with the fixing ring, prevents axial movement of the adjusting screw.

Punch assembly

Growing community of inventors

Shenzhen, China

Jian Luo