Other

Ditto Sales, Inc.

Bissell Inc.

Hoffman, James P.

Hoffman, Jeremy P.

Macmillan, Robert

Jeremy P Hoffman

Robert MacMillan

Jeffrey A Scholten

Jason W Pruiett

James P Hoffman

Danielle Boils

JianJun Yu

Jian Jun Yu

Jianjun Yu

A crown molding assembly that enables safely incorporating electrical and communications cabling within the crown molding by providing segregated compartments for electrical and copper communications cabling, wherein the decorative face is formed of a composite of fiber reinforcing polymer (FRP) including a fiber-reinforced structure having an increased directionality of said reinforcing fibers causing the decorative face to fracture upon being pierced by a fastener in a manner that renders the damaged section of the decorative face unable to hold the fastener, protecting the electrical cables and any other equipment located behind the decorative face from damage, and enables the secure installation of hardware either concealed within the molding or securely and favorably positioned through the decorative face to view or sense a room, and enables additional cable capacity that is concealed within a light reflector to increase lighting efficacy and power and data delivery capacity.

Crown molding assembly formed of a composite of fiber reinforcing polymer and having segregated compartments for routing power and communications cables

A system and method for relocating branch circuit electrical cables which enter an existing electrical enclosure, and for which additional cable length is unavailable, to a novel enclosure presenting cable entry points favorably positioned to receive the existing branch circuit cables without additional length required, and in a manner considered safe and repeatable for multiple branch circuit cables to be relocated at present or in the future.

System and method for relocating branch circuit electrical cables from an existing electrical enclosure

A system for crown molding that enables safely incorporating electrical and communications cabling within crown molding by creating one or more protected paths which inherently prevent overly sharp bends in crown molding corners and by mitigating damage from penetrating punctures through a decorated face designed to fracture when improperly penetrated by a screw or nail, and enables the secure installation of hardware either concealed within the molding or securely and favorably positioned through the decorative face to view or sense a room, and enables additional cable capacity that is concealed within a light reflector to increase lighting efficacy as well as power and data delivery capacity.

System and method for securing power and communications cables and associated hardware within crown molding

An ultrasonic cleaning tool for cleaning a surface has a transducer and a horn for generating and transmitting vibrations to a surface to be cleaned. Cleaning solution can be supplied to the ultrasonic cleaning tool or the surface to be cleaned, and operation of the ultrasonic cleaning tool can agitate the surface and cleaning solution. The tool can be provided as part of a system for cleaning a surface, and the system can include an extraction cleaner or a cleaning cloth.

Ultrasonic cleaning tool and system for cleaning a surface

A system and method comprised of an LED light strip whose electrically insulating core structure is somewhat flexible and elastic and whose alternating light producing sections and narrower clip sections have a top side containing LED elements and control signals and an underside containing a high capacity voltage bus, and a three sided mounting structure where an installed LED light strip is the fourth side with LED elements facing out and the voltage bus protected inside, and a clip system of two halves which affix to each other around a narrower clip section with a lower half connecting electrically to the voltage bus under the narrower clip section and installing in one side of the mounting structure and an upper half connecting electrically to control signals on the top half of the narrower clip section and installing in the other side of the mounting structure.

LED light linear strip, mounting structure and clip assembly

A unitary longitudinal wall attached structure of consistent profile for installation on a wall having an attachment portion which is securely affixed to the wall, an inherently flexible pivot or hinge portion whose upper end is attached to the attachment portion and whose lower end is attached to a rigid pivoting body whose center of mass is below and spaced outwardly from the wall relative to the hinge portion and gravity when preferably installed, where the wall is angled no more than 45 degrees and is secured to the larger structure within which the wall attached structure is to be installed, with said installation enabling an intra-structural pendulum where the secured attachment portion anchors the pendulum, and the inherently flexible hinge portion enables the pivoting body as it urges its lower contact surface against the wall.

Wall-attachment structure and system employing an intra-structural hinge for reinforcing preferred placement on a straight or curved wall

A molding system installed at or near the top of a vertical wall having a molding portion and an attachment portion, where the attachment portion is attached securely to the wall above at least the center of mass of the molding portion, and the molding portion has an outwardly visible decorative face which extends down to where the lower edge of the molding portion meets the wall. The attachment portion is enabled to flex as it is firmly attached to an imperfect wall, and the structure of the molding portion is such that the decorative face of the molding system remains preferentially straight and preferentially positioned as the molding system is installed on an irregular wall. A hinge-like flex is enabled along the length of the molding above the center of mass of the molding portion such that the decorative face of the molding can pivot like a pendulum ensuring the lower edge of the molding is placed against the wall. None of the methods of installation of this system violate the decorative face of the molding and a consistent decorative face profile extends around the entire installation.

System and method for installation of crown molding on imperfect walls

A molding system for use in interior spaces at or near the top of a vertical wall having a decorative surface and a vertical mounting surface including an attachment flange used for fastening the molding section to the wall, said molding section having a center of mass which is spaced outwardly from the wall surface, and whereby the point of attachment of said molding to the wall is located at a vertically higher position on the molding section than the center of mass so that when secured to a wall the lower end of the molding section is continually urged towards the wall surface and is therefore maintained in continual contact with the wall surface.

System and method for installation of decorative molding

An article of furniture has been developed having a tilting tabletop mechanism, which securely maintains a tabletop in either a generally horizontal or generally vertical position while permitting a user to tilt the tabletop easily. The article of furniture includes a first component, a second component, a first member, a second member, a first lock element, and a second lock element. The second component is pivotally coupled to the first component. The first and second members are connectable to a first secured component. The first secured component is one of the first and second components. The first lock element is mounted to engage the first member when the first component is in a first position relative to the second component. The second lock element is mounted to engage the second member when the first component is in a second position relative to the second component.

Growing community of inventors

Newtown, PA, United States of America

Jeremy P Hoffman