Te Connectivity Corporation

Te Connectivity Solutions Gmbh

Te Connectivity Services Gmbh

Other

Tyco Electronics Brasil Ltda

Te Connectivity Brasil Industria De Eletronicos Ltda

Jeremy Christin Patterson

Weiping Zhao

David Bruce Sarraf

Aaron James De Chazal

Kevin John Peterson

Amadeu Luiz Fazani Cavallieri

Xiaobao Geng

Clara Marguerite Rhodes

John Mark Myer

Hurley Chester Moll

David James Rhein

Zachary Wood Lyon

Matthew Bryan Hitchcock

Nathan Philip Myer

Christopher Ryan Raybold

Ryan David Hetrick

Dinesh Loku Hemnani

Andre E Guanco

Thomas Wojtacki

Eric Shields

Scott Cross

Shanoo Revankar

A connector for a flat flexible cable includes a housing and a terminal disposed in the housing. The housing has a base and a cover. The base has a closed section with a receiving passageway and an open section extending from the closed section. The cover encloses the open section in a closed position of the cover. The cover has a main body with a pressing surface and a latch extending from the main body. The latch engages a catch of the base in the closed position. The terminal is disposed in the receiving passageway and has a tab extending into the open section. The pressing surface abuts the tab and presses the tab toward the base in the closed position.

Connector for a flat flexible cable

A resistor module includes a resistor module housing having an inner cavity. A proximity contact and a ground contact are received in the inner cavity and held by the resistor module housing. A proximity wire, electrically connected to a proximity terminal of the charging inlet assembly, is electrically connected to the proximity contact. A ground wire, electrically connected to a ground terminal of the charging inlet assembly, is electrically connected to the ground contact. A resistor element is received in the inner cavity and coupled to mating ends of the proximity and ground contacts. The resistor element is electrically connected to the proximity terminal through the proximity wire and the proximity contact and is electrically connected to the ground terminal through the ground wire and the ground contact.

Resistor module for a charging inlet assembly

A battery distribution unit includes a housing having a bottom mounted to a battery case of a battery module and having a component cavity with a contactor therein. The contactor has fixed contacts having terminating ends extending from a bottom end of a contactor housing. The BDU includes terminals at the bottom end of the contactor coupled to the terminating ends and a heat exchanger cap at the bottom end of the contactor. The heat exchanger cap is provided in the component cavity in thermal communication with the fixed contacts and in thermal communication with the battery case of the battery module to dissipate heat from the fixed contacts into the battery case of the battery module.

Heat dissipation arrangement for battery distribution unit

A battery module frame includes first and second frame sections each having a main body, an upper side wall extending from the main body, and a lower side wall extending from the main body. The main body has a bus bar pad for a bus bar that is configured to be electrically connected to battery cells of the battery module. The upper and lower side walls include upper and lower mounting features. The first and second frame sections are coupled at a seam with the upper mounting features removably coupled together at an upper separable interface and with the lower mounting features removably coupled together at a lower separable interface. The first and second frame sections are coupled together with the bus bar pads of the main bodies coplanar.

Battery module frame for a battery module of a battery system

A charging inlet assembly for an electric vehicle includes a housing having a power connector including AC terminals and DC terminals. An AC terminal assembly is coupled to the housing and includes AC bus bars electrically connected to corresponding AC terminals at a separable mating interface. A DC connector is mechanically and electrically connect to the DC contact of the DC connector at a separable mating interface.

Charging inlet assembly

A cooling system for a power connector of a charging inlet assembly includes a cooling adapter coupled to a housing of the charging inlet assembly including an adapter body forming a cavity. The cooling adapter includes supply and return ports adjacent a cable exit. The cooling system includes a heat exchanger positioned in the cavity of the cooling adapter including a heat exchanger body configured to receive the power cable and/or the terminal. The heat exchanger body is thermally coupled to the power cable or the terminal to dissipate heat therefrom.

Heat exchanger for a power connector

A bus bar module of a battery system includes a bus bar, a sensing circuit carrier, and a fuse assembly. The bus bar is held by a tray and configured to electrically connect two battery cells of the battery system. The sensing circuit carrier includes at least a first electrical conductor and a dielectric insulator surrounding the first electrical conductor. The fuse assembly includes a first holder terminal, a second holder terminal, and a fuse disposed between and electrically connected to the first and second holder terminals. The first holder terminal is electrically connected to the first electrical conductor of the sensing circuit carrier, and the second holder terminal is electrically connected to the bus bar such that the fuse assembly defines a segment of a voltage sensing line from the bus bar through the sensing circuit carrier towards a control device.

Battery bus bar module

A high voltage diagnostic connector includes a housing holding a positive terminal, a negative terminal and a ground terminal with a cover removably coupled to the housing. An HVIL assembly is in the housing having a HVIL contacts and an HVIL shunt. An HVIL switch is held by the housing including a shunt actuator operably coupled to the HVIL shunt to position the HVIL shunt in an un-shunted position to open an HVIL circuit when in the primary position and in a shunted position to close the HVIL circuit when in the secondary position. The shunt actuator is movable between the primary position and the secondary position when testing the positive terminal, the negative terminal and the ground terminal with the testing device during diagnostic testing of the high voltage diagnostic connector.

High voltage diagnostic connector with service disconnect

A cover assembly for a battery module is configured to be coupled to battery cells that are arranged side-by-side in a stacked configuration. The cover assembly includes a housing, a plurality of bus bars, and an electrical cable. The bus bars are held by the housing and are configured to electrically connect to corresponding positive and negative cell terminals of the battery cells to electrically connect adjacent battery cells. The cable extends across the bus bars and is electrically connected to each of the bus bars to monitor voltages across the battery cells. The cable includes plural electrical conductors and a dielectric insulator that surrounds and electrically isolates the conductors. The conductors include exposed segments exposed through the dielectric insulator that are electrically connected to corresponding bus bars via a bonding layer applied between the exposed segment and the corresponding bus bar.

Cover assembly for a battery module

An electrical module is configured to be coupled to a tray of a battery distribution assembly. The electrical module includes a housing disposed along an outer surface of the tray. The electrical module also includes at least one electrical circuit device disposed within a cavity of the housing. The electrical module further includes multiple terminals electrically connected to the at least one electrical circuit device. The terminals project outward from the housing and extend through corresponding apertures in the tray for electrically connecting to one or more electrical conductors disposed along an inner surface of the tray.

Electrical module for battery distribution assembly

A conduit support bracket is provided. The support bracket has an elongated base that can be secured to a pair of adjacent joists having a space between the joists. The support bracket has a vertical support arm secured to the base at one end of the arm. The length of the support arm is adjustable. A support platform is secured to the opposite end of the support arm. The support platform can be rotated both horizontally and vertically to adjust the orientation of the support platform. As many support brackets as needed may be used at intervals to support a length of conduit in an elevated position above joists.

Growing community of inventors

Winston-Salem, NC, United States of America

Jeremy Christin Patterson