University of North Florida

Other

Jay S Huebner

Rodolfo T Arrieta

Nirmalkumar G Patel

Doria F Bowers

Jason J Saredy

Brian E Stadelmaier

Erica N Mejia

A device and method which comprises a sensing surface on a membrane, solid surface or electrode, where the sensing surface contains a dye or chromophore chosen in relation to a particular target substance to be detected and quantified. The dye or chromophore is of a type which produces an electrical signal upon illumination. The particular dye or chromophore chosen for a particular target substance is one in which the presence of the target substance causes a change in the electrical signal produced. The presence of the target substance modifies the expected photo-induced charge movements (PICM) produced by the sensing surface upon illumination. The photo-induced charge movements produce signals which are detected by electronic circuits, and the presence and concentration of the target substance is determined by analyzing the difference between the PICM of the target sample versus the PICM of a control sample lacking the target substance.

Sensing device and method using photo-induced charge movements

A device and method which comprises a sensing surface on a membrane, solid surface or electrode, where the sensing surface contains a photo-voltage active material chosen in relation to a particular target substance to be detected and quantified. The photo-voltage active material is of a type which produces an interfacial photo-voltage electrical signal upon illumination. The particular photo-voltage active material chosen for a particular target substance is one in which the presence of the target substance causes a change in the electrical signal produced. The presence of the target substance modifies the expected photo-voltage produced by the sensing surface upon illumination. The photo-voltage produces signals which are detected by electronic circuits, and the presence and concentration of the target substance is determined by analyzing the difference between the photo-voltage of the target sample versus the photo-voltage of a control sample lacking the target substance.

Photoelectric chemical sensor and sensing method utilizing interfacial photo-voltages

A nanocrystalline ITO thin film formed on a quartz crystal microbalance (QCM) facilitates detection of gaseous compounds emitted from an analyte. Adsorption of gas molecules onto the nanocrystalline ITO thin film changes the resonant frequency of the quartz crystal. Parameters such as the frequency of oscillation, surface resistance, integrated frequency response, integrated surface resistance response, initial response slope, average return to baseline slope, and/or return to baseline time/initial response time ratio of the quartz crystal with the nanocrystalline ITO thin film formed thereon are determined. Using the determined parameters and principal component analysis, principal components for the gaseous compounds are also determined. These determined principal components may be compared with known principal components corresponding to known analytes. The analyte may include any distinguishable substance, in any state that emits at least one gaseous compound that can be adsorbed on the nanocrystalline ITO thin film. Nonlimiting examples of analytes include alcoholic beverages, fruits, explosive compounds, VOCs, petroleum-based fuels, alkanes, aldehydes and ketones.

Quartz crystal microbalance with nanocrystalline oxide semiconductor thin films and method of detecting vapors and odors including alcoholic beverages, explosive materials and volatilized chemical compounds

A system for detecting a wide range of microbial organisms, including virus, and determining concentrations in near real-time to determine titer, without the requirement to grow micro-organisms includes an electrometer configured to measure photo-induced interfacial voltages and an electrode assembly with a substrate and at least one electrode on a surface of the substrate electrically coupled to the electrometer. An attachment factor is applied to an exposed surface of each electrode. The attachment factor is effective for interaction with the microbial organism. A transparent vessel for containing the electrolytic solution is provided. The microbial organism may be contained in the electrolytic solution or applied to the coated electrode before being submerged in the electrolytic solution. A light source is configured to controllably produce a flash of activating light directed through the transparent vessel at the electrode causing a sensible photo-induce interfacial voltage indicative of the microbial organism and titer. A corresponding method includes steps of preparing the electrode surfaces with an attachment factor and exposing the submerged electrode surfaces to a flash of activating light to induce interfacial voltages indicative of a determined microbial agent and titer.

Growing community of inventors

Jacksonville, FL, United States of America

Jay S Huebner