Schweitzer Engineering Laboratories, Inc.

Jay Hartshorn

Marcos A Donolo

Subhash C Patel

Vinod K Yedidi

Veselin Skendzic

Angelo D'Aversa

Anushka M Dissanayake

Normann Fischer

Chandrasekaran Swaminathan

Jianchun Qin

Yusuf Zafer Korkmaz

Pallavi Kulkarni

Andrea Di Tomasso

Hang Li

A system for high-impedance differential protection for power systems using a variety of signals from the power system. A fault may be detected using filtered phase current or filtered phase voltage magnitudes from current transformers (CTs) connected in parallel by phase. A fault may be detected using filtered phase voltages and raw phase voltages from the CTs. A fault may be detected using raw phase currents and raw phase voltages from the CTs. A fault may be detected using filtered phase currents and raw phase currents. A fault may be detected using raw phase currents and raw neutral currents. The embodiments herein maintain dependability and security of a differential element even when low-class CTs are used. The embodiments herein may allow users to optimize pickup settings even when low-class CTs are used.

High-impedance differential protection using a diversity of signals

Signal transducers in electrical communication with shorted leads of current transformers are used to provide monitoring and protection functions to an electric power delivery system. Differential protection is performed by comparing a predetermined threshold against a voltage signal from series-connected leads of signal transducers in electrical communication with shorted leads of current transformers. The signal transducers may be Rogowski coils. Signal transducers in communication with shorted leads may be used to improve safety and increase performance of the current transformers by decreasing susceptibility to saturation.

Differential protection using instrument transformer signal transducers

Systems and methods may be used to measure a frequency of a power delivery system and/or of a supply signal transmitted to a load. A system may record an input waveform, determine a frequency of the input waveform at a present time based at least in part on the input waveform and a derivative of the input waveform, and control an operation of a power delivery system based at least in part on the determined frequency.

Frequency sensing systems and methods

Differential protection of electric power delivery system equipment using a compensated operating signal under spurious conditions is disclosed herein. Current transformers (CTs) may provide spurious current signals under certain operating conditions resulting in unintended operation of differential protection. The present disclosure uses a compensated operating signal during such conditions. The compensated operating signal is calculated using operate current and a difference between direct current content of currents obtained from the CTs. Switching between use of the operate current and the compensated operating signal is based on a comparison of the average direct current content of the CTs and a threshold.

Electric power system differential protection with DC compensation

A method includes receiving electrical measurements of an input signal of a power system. The method includes determining an estimated frequency of the power system using a rate of change of phase of the power system and using zero crossings of the power system. Selection between using the rate of change of phase of the power system and using zero crossings of the power system is based on a comparison between an estimated phase angle and a measured phase angle of the power system.

Frequency measurement for load shedding and accurate magnitude calculation

An intelligent electronic device (IED) according to the present disclosure can estimate a full load rotor resistance value as a function of motor positive-sequence resistance. The IED may estimate the full load rotor resistance value by measuring zero-crossings of voltage after a motor disconnect. The IED may also acquire motor current and voltage measurements and calculate motor slip using the acquired motor current and voltage measurements and the estimated full load rotor resistance value.

Induction motor slip calculation

In-phase transfer of an electric power source to a load bus from a first feeder to a second feeder is disclosed herein. Voltage phase difference, voltage frequency difference, and voltage rate-of-change of frequency difference, between the second feeder and the load bus are used along with a breaker delay time to determine whether the breaker will close while the phase of the second feeder and the load bus are within an acceptable range. One or more breaker close time checks may be performed, including a breaker close time consistency check and a breaker close time uncertainty check.

In-phase motor bus transfer

Monitoring conditions of an electric motor using stator current and voltage signals from power supplied to the motor is disclosed herein. The stator voltage and current signals may be used to calculate instantaneous power values which may be used to calculate slip. The slip may be used to monitor for a locked rotor condition during startup of the motor. The slip value may be used to provide thermal protection to the electric motor.

Growing community of inventors

Moscow, ID, United States of America

Jay Hartshorn