Lucent Technologies Inc.

Marotta Controls, Inc.

Other

James Thomas LaGrotta

Richard Thomas LaGrotta

Krzysztof Kluz

Alexander Colletti

Christopher Strianse

Brian Ippolitto

Maxwell Wolfinger

Christopher Modin

Christian Skawski

Jon W Engelberth

Harry C Beals, Jr

Manuel G Orellana

James Christopher Coyne

Victor Kaminski

Ronald B Walsh, Jr

Joseph V Newell

John M Carcone

Patrick Boyle

Carly Elisa LaGrotta

James Ponzo

An electronic pressure regulation system includes an electronic control unit and a fluid assembly, with the fluid assembly including a fluid control branch having a proportional control valve and a heater. The heater may be a strip heater applied to or a coil wrapped around an external surface of the proportional control valve. The system may further include a latching isolation valve. A secondary fluid control branch can be included, and the fluid control branches can be in parallel. The electronic pressure regulation system can be included in an all-electric satellite. Another electronic pressure regulation system includes an electronic control unit and a fluid assembly, with the fluid assembly including a fluid control branch having a proportional control valve, the proportional control valve including two independently-controlled coils for magnetostrictive actuation.

Electronic pressure regulation system with proportional control valve

A solenoid operated valve includes a valve block defining a valve lumen, a poppet slidably disposed within the valve lumen, a solenoid including a core defining a core lumen aligned with the valve lumen, and an armature assembly. The armature assembly includes an armature disc, an armature guide having a hollow cylindrical body defining an armature guide passage, and an armature stud disposed within the armature guide passage. The armature stud is in communication with the poppet so that axial movement of one is translated into axial movement of the other. The valve further includes a coil cover enclosing the solenoid, and a guard disposed to prevent contact between the armature assembly and an adjacent component of the valve. A method of assembling a solenoid operated valve includes placing a shim between the armature disc and the core, and pressurizing and energizing the valve.

Solenoid valves for high vibration environments

An electronically-controlled pressure regulator includes an inlet through which a gas or liquid is introduced at an inlet pressure, an outlet through which the gas or liquid exits at an outlet pressure, and a valve disposed between the inlet and the outlet, the valve defining a passage including a throat and having a pintle with an enlarged shoulder, the valve movable between a closed configuration in which the enlarged shoulder seals the throat to prevent the gas or liquid from passing from the inlet to the outlet through the valve, and an open configuration in which the gas or liquid can pass from the inlet to the outlet through the valve. In a valve flow path, the enlarged shoulder is disposed between the inlet and the throat. All of the gas or liquid that enters through the inlet can exit through the outlet.

Electronically controlled regulator

A fire extinguishing system is disclosed in which the system comprises a fire extinguisher having an opening, and a valve assembly covering the opening. The valve assembly includes a valve movable from a first position in which the valve seals the opening of the fire extinguisher to a second position in which the valve exposes the opening to allow expulsion of fire suppression material(s) from the fire extinguisher. A release mechanism, which may be in the form of a solenoid or a manual release mechanism, is provided for moving the valve to its open position. Methods of using the aforementioned fire extinguisher to suppress a fire are also disclosed.

Method and mechanism for fast evacuation of a pressurized vessel

A method is disclosed for the fabrication of a tunable radio frequency (RF) power output filter that includes fabricating a core body and then forming a plastically deformable metallic shell over the exterior surface of the core body.

Method of constructing a tunable RF filter

A method of remotely locating a mobile device equipped with a radio receiver by remotely and securely activating the device's ringer and location system, and communicating such location to the device owner.

Method of remotely locating a mobile device equipped with a radio receiver

Low profile plug-in GFI device

On instructions obtained from a subscriber, a wireless terminal service provider sends a power-down signal to a wireless terminal. Upon receipt of the power-down signal, the wireless terminal goes into a sleep state. In this state, all monitoring functions other than time, date and elapsed time are turned off. The power-down signal sets a clock, which can be located within the wireless terminal, to awaken the wireless terminal at the end of a discrete interval of time by powering-up the monitoring circuits. The wireless terminal service provider, by knowing the power-down/power-up time cycle of the wireless terminal, can alert a party attempting to contact the wireless terminal during the power-down period that the called party cannot be reached. The wireless terminal service provider can also offer various options to the calling party, such as providing the time when the called wireless terminal will next be on, offer to take a message which can be sent when the called wireless terminal is next on, offer to cancel any further attempt to send the message to the called wireless terminal, etc. Normally, the power-down control signal will condition the wireless terminal to assume the sleep state for a discrete interval of time. Extended intervals of time can be obtained by resending the control signal at the end of the discrete interval of time. If desired, a two-part control signal can be sent to the wireless terminal where one part conditions the wireless terminal to assume the power-down state and the other part controls the duration of the power-down state.

Remote power-down control of wireless terminal

A power connector for receipt and releasable engagement with a wire to effect a transmitting power electrical connection to the wire. The power connector includes a connector housing having a wire insertion side with an opening for receiving the wire. A spring contact is disposed within the housing and includes an attachment end for attaching the spring contact to the connector housing and a contact end for contact with the wire. The spring contact includes a substantially C-shaped segment extending between the attachment end and contact end. The C-shaped segment is dimensioned to be maintained under compression and so that the spring contact applies a contact force against an inserted wire at the contact end with a force sufficient for supporting the conducting of electricity between the wire and contact end. The C-shaped segment is further oriented so that when a lateral force is imparted to the C-shaped segment from the wire-insertion side of the housing, the contact force applied against the wire is reduced to thereby reduce the force required to disengage and remove the wire from the connector housing.

Power connector for releasable engaged retention of a wire

A mounting assembly includes a metallic base member, such as a wall of an enclosure. A threaded stud is fused to the base member. A threaded collar engages the threaded stud and provides a threaded recess for receiving a mounting fastener. The mounting assembly is well-suited for supporting electronic items within an enclosure in a weather-tight or water-proof manner because the mounting assembly requires no seals for an environmental barrier.

Mounting assembly for an enclosure

A heating/cooling apparatus for electronic components of a wireless base station is described. The apparatus includes a heat exchanger having a material-filled chamber and a plurality of extrusions. The chamber is located adjacent to the electronic components. A heater is provided within the chamber. The material within the chamber, which is preferably a liquid, serves to conduct heat from the electronic components to the extrusions. The heater serves to heat the material within the chamber, which in turn conducts that heat to the electronic components, when heat is required to maintain operation of the components with prescribed parameters.

Method and apparatus for heat regulating electronics products

A lockable piano-type hinge assembly including a locking hinge piece in addition to two hinge pieces which include the hinge pin barrels. The hinge pin is secured to the locking hinge piece which has an opening aligned with a locking loop secured to one of the hinge pieces. When the hinge assembly is assembled, the locking loop extends through the opening of the locking hinge piece and a locking device is insertable through the locking loop to prevent relative movement of the locking hinge piece and removal of the hinge pin from the barrels.

Lockable hinge assembly

Outdoor, electronic component containing cabinets are cooled by forced circulation of outside air through the cabinet for direct, cooling contact with the components. The incoming air is filtered, heated as necessary to evaporate water droplets in the air prior to entry of the air into the component containing portions of the cabinet, and the air flow is regulated for slowing the flow rate of the air within the cabinet as is necessary for maintaining the relative humidity within the cabinet below a maximum percentage; typically 40%.

Growing community of inventors

Boonton, NJ, United States of America

James Thomas LaGrotta