Silicon Laboratories Inc.

Massachusetts Institute of Technology

James T Kao

Adrian Maxim

Abdulkerim Coban

Alessandro Piovaccari

Ramin Khoini-Poorfard

Masayuki Miyazaki

Anantha P Chandrakasan

Ramin Khoini Poorfard

A signal processor for a radio frequency (RF) receiver includes a signal processing path having first and second programmable gain amplifiers and first and second offset correction circuits. The first offset correction circuit receives a first digital offset correction word and corrects a first offset of the first programmable gain amplifier by adding a first value corresponding to the first digital offset correction word to an input of the first programmable gain amplifier. The second offset correction circuit receives a second digital offset correction word and corrects a second offset of the second programmable gain amplifier by adding a first value corresponding to the second digital offset correction word to an input of the second programmable gain amplifier. A controller measures offsets of the first and second programmable gain amplifiers during a calibration, and provides the first and second offset correction words in response to the offsets.

Signal processor suitable for low intermediate frequency (LIF) or zero intermediate frequency (ZIF) operation

A signal processor for a radio frequency (RF) receiver includes a plurality of distributed signal processing elements, in which a first one receives an input signal and a last one provides an output signal, and a plurality of gain elements interspersed between pairs of said plurality of distributed signal processing elements. The signal processor also includes a like plurality of peak detectors coupled to outputs of corresponding ones of said plurality of gain elements, and an automatic gain controller having inputs coupled to outputs of each of the peak detectors, and outputs coupled to each of the plurality of gain elements. The automatic gain controller independently controls each of the plurality of gain elements to form a like plurality of independent automatic gain control (AGC) loops.

A reference clock generator includes an oscillator to generate a periodic signal, a shaping circuit and a filter. The shaping circuit shapes the periodic signal to generate a clock signal. The filter is located between the oscillator and the shaping circuit.

Providing a low phase noise reference signal

A technique includes receiving a signal spectrum that includes a plurality of channels within a first frequency range. The technique includes receiving a selection signal that identifies at least one desired channel to be tuned. The technique includes providing an oscillator that has a second frequency range that is substantially the same as the first frequency range and controlling the oscillators to generate one of a plurality of coarse-tune analog mixing signals. The signals substantially span across the second frequency range and each depends upon the location of the desired channel within the signal spectrum. The technique includes mixing the signal spectrum with the selected coarse-tune analog mixing signal to generate a coarsely tuned signal spectrum. The technique includes digitally processing the coarsely-tuned signal spectrum to fine tune the desired channel and to produce digital baseband signals for the desired channel.

Receiver architectures utilizing coarse analog tuning and associated methods

Several open-loop calibration techniques for phase-locked-loop circuits (PLL) that provide a process, temperature and divider modulus independence for the loop bandwidth and damping factor are disclosed. Two categories of open-loop techniques are presented. The first method uses only a single measurement of the output frequency from the oscillator and adjusts a single PLL loop element that performs a simultaneous calibration of both the loop bandwidth and damping factor. The output frequency is measured for a given value of the oscillator control signal and the charge-pump current is adjusted such that it cancels the process variation of the oscillator gain. The second method uses two separate and orthogonal calibration steps, both of them based on the measurement of the output frequency from the oscillator when a known excitation is applied to the open loop signal path. In the first step the loop bandwidth is calibrated by adjusting the charge-pump current based on the measurement of the forward path gain when applying a constant phase shift between the two clocks that go to the phase frequency detector, while the integral path is hold to a constant value. During the second step the damping factor is calibrated by adjusting the value of the integral loop filter capacitor based on the measurement of the oscillator output frequency when excited with a voltage proportional with the integral capacitor value, while the proportional control component is zeroed-out.

Method and apparatus to achieve a process, temperature and divider modulus independent PLL loop bandwidth and damping factor using open-loop calibration techniques

A system for improving the power efficiency of an electronic device includes a threshold voltage selector and a supply voltage selector. The threshold voltage selector selects a value of a threshold voltage for operation of the device in response to a present operating condition of the device. The supply voltage selector selects a value of a supply voltage to be applied to the device in response to the present operating condition of the device. The value of the threshold voltage and the value of the supply voltage control a power consumption of the device.

Growing community of inventors

Austin, TX, United States of America

James T Kao