Rockwell Automation Technologies Incorporated

Eja Limited

Rockwell Automation Safety Ag

Rockwell Automation Switzerland Gmbh

James Edward Dogul

George E Rollins

Derek William Jones

Suresh Ramanujan Nair

Richard Galera

Ray Carlisle Delcher

George Karl Schuster

Burt Sacherski

Steven Robert Tambeau

Todd Bubar

Andrew L Tsang

Arvind Ananthanarayanan

Francis Lawrence Leard

Hassan R Manjunath

Anthony Gerard Gibart

Wayne R Foster

Carl Meinherz

Martin Hardegger

Julian Poyner

Timothy P Wolfe

Danilo Dorizzi

Joshua D Vavra

Prachi S Kulkarni

Christopher Walther

Arvid Ananthanarayanan

George K Schuster

A cable pull switch includes a polychotomous sensor configured to provide a reading of at least one of a plurality of values, the reading corresponding to a tension on a pull cable or a linear displacement of an end of a pull cable. A processor coupled to the polychotomous cable pull sensor configured to determine a rate of change of the value of the reading from the sensor and determine an occurrence of a cable pull event, the determination based on the determined rate of change of the value, and determine whether the rate of change of the value of an electrical resistance through the polychotomous cable pull sensor is below a threshold rate of change value, and adjust an upper pull threshold value to a new upper pull threshold value that is based on a present reading of the value of the electrical resistance through the strain gauge.

Safety switch and associated methods

An apparatus for an imbalance test includes a strain measurement module that measures a strain voltage across terminals of a strain gauge. The strain voltage is representative of an amount of force on the strain gauge. The apparatus includes a test measurement module that measures a test voltage across the terminals of the strain gauge while a test resistor is connected in parallel with a resistor of the strain gauge. The test resistor is connected while the test measurement module measures the test voltage and is disconnected while the strain module measures strain voltage. The apparatus includes an average module that calculates an average strain voltage from two strain voltage measurements. The strain voltages are measured preceding and after the test voltage measurement. The apparatus includes a difference module that determines a difference voltage. The difference voltage is a difference between the average strain voltage and the test voltage.

Safety switch with imbalance test

A control assembly includes a locking device having at least a first mode of operation and a second mode of operation, the locking device configurable to change from the first mode of operation to the second mode of operation. The locking device has a non-contact sensor and a microcontroller. An independent communicator is configured to communicate configuration data to the microcontroller. The microcontroller is configured to change from the first mode of operation to the second mode of operation using configuration data received from the independent communicator.

Locking switch assembly and related methods

A cable pull switch includes a polychotomous sensor configured to provide a reading of at least one of a plurality of values, the reading corresponding to a tension on a pull cable or a linear displacement of an end of a pull cable. A processing device is configured to receive the reading, determine whether a value of the reading is outside of a non-tripped value window, a limit edge being a pull threshold value, and responsively generate an output signal indicative of a cable pull event. Other features and improvements are described.

The present invention relates to a transceiver element for an optical unit of a photoelectric barrier to such a photoelectric barrier. In particular, a transceiver element comprises at least one optical sender, at least one optical receiver and a control element, wherein said control element comprises a driver unit for driving said at least one optical sender to emit radiation and at least one receiver unit for sensing and evaluating electrical signals generated by said optical receiver.

Transceiver element for an optical unit of a photoelectric barrier and photoelectric light curtain

Apparatus and methods for using infra-red light provide for enhanced operation in camera applications. In an embodiment, a safety camera includes an optical filter that provides an input to an imager from received light having wavelengths in the infra-red spectrum. Output from the imager can be analyzed to determine safety hazard events in an area viewed by the safety camera.

Apparatus and methods for camera applications

Apparatus and methods for use of infra-red light in camera applications

Apparatus and methods for using a tunable optical source in safety curtain applications provide for enhanced operation of the safety curtain. In an embodiment, a safety curtain includes a transmit unit and a receive unit to operate as the safety curtain, where a single tunable light source generates different wavelengths of light and a single detector is used to detect the generated light.

Apparatus and methods for use of a tunable optical source in safety curtain applications

System(s) and method(s) that facilitate utilizing biometric sensors (e.g., fingerprint, hand scan, voice recognition . . . ) in manufacturing systems in order to maintain accurate safety audit trails. A safety audit system, utilizing a biometric sensing device, facilitates determining if a user is allowed to access and change the configuration of the manufacturing system. Once a user is allowed to change the configuration (e.g., programmable electronics, tooling changes, software updates, etc.) the changes are automatically recorded in a safety audit database. Automatic storage of configuration changes mitigates manual recording of changes thereby enhancing the safety audit data often necessary to meet safety standards for manufacturing systems.

Audit trail in a programmable safety instrumented system via biometric signature(s)

The claimed subject matter provides a system and/or a method that facilitates providing a safety mechanism associated with a protective zone in an industrial automation environment. An radio frequency identification (RFID) component can receive data from an RFID tag to identify a location. A safety component can employ a safe mode to a device based at least in part upon the location to employ a protected zone in proximity with the device.

RFID/biometric area protection

The claimed subject matter provides industrial automation systems and/or methods that configure available redundancy. An interface component can obtain input data. Additionally, an optimization component can generate a voting configuration that allocates available redundancy to provide an optimized combination of safety and availability based at least in part on the input data.

Optimizing availability and safety by reconfiguring and auto-adjusting redundancy

An industrial device comprises a light emitter and a detector that is optically coupled to the emitter. A first deformable mirror/lens is optically coupled to the emitter, the first deformable mirror/lens is dynamically shaped to facilitate receipt of light at the detector. For example, the deformable mirror/lens can be associated with one or more actuators that causes the mirror/lens to be shaped in a desirable manner.

Industrial device with adaptive optics

The claimed subject matter provides a system and/or a method that facilitates initiating a sequence within an industrial automation environment. A radio frequency identification (RFID) component can receive data from an RFID tag. An event control component can invoke at least one event related to a device in a designated control sequence.

Growing community of inventors

Hudson, NH, United States of America

James Edward Dogul