Credence Systems Corporation

Other

Schlumberger Technologies, Inc.

Nptest, Inc.

Howard Maassen

William A Fritzsche

Jean-Yann Gazounaud

Burnell G West

Toshihiro Nomura

Thomas P Ho

Joseph C Helland

Angarai T Sivaram

A system and method for reducing timing errors in automated test equipment (ATE) offering increased data rates for the testing of higher-speed integrated circuits. Embodiments provide an effective mechanism for increasing the data rate of an ATE system by delegating processing tasks to multiple test components, where the resulting data rate of the system may approach the sum of the data rates of the individual components. Each component is able to perform data-dependent timing error correction on data processed by the component, where the timing error may result from data processed by another component in the system. Embodiments enable timing error correction by making the component performing the correction aware of the data (e.g., processed by another component) causing the error. The data may be shared between components using existing timing interfaces, thereby saving the cost associated with the design, verification and manufacturing of new and/or additional hardware.

Method and system for correcting timing errors in high data rate automated test equipment

A driver block for a differential pin driver that supports out-of-band signaling. The driver block includes a main enable switch that is controlled by a high speed driver inhibit (DINH) signal. The main enable switch controls coupling between a main current source and a differential pin driver output stage. The main enable switch is coupled in series with an output select switch that selects between a positive output and a negative output. The driver block also includes a positive enable switch for controlling coupling between the positive output and a positive level shifter that shifts voltages of the positive output. The driver block also includes a negative enable switch for controlling coupling between the negative output and a negative level shifter that shifts voltages of the negative output.

High speed, out-of-band differential pin driver

A test apparatus implements a method for testing electronic devices that exhibit non-deterministic behavior. The test apparatus includes a high-speed buffer queue for storing data packets. The data packets arrive at one end of the queue and, as they exit at the other end, are compared against expect data packets stored in memory. If the data packet exiting the buffer queue corresponds to response signals generated by the device under test during a non-deterministic (e.g., idle) state, the expect data packet is not retrieved from memory and the comparison is not made.

Non-deterministic protocol packet testing

Method and apparatus for calibrating timing accuracy during testing of integrated circuits. An ATE type (automatic test equipment) integrated circuit tester calibrates itself to reference blocks (dummy ICs) that have the same relevant dimensions as the integrated circuits to be tested and have fit into the test fixture. The number of reference blocks required is equal to the number of signal terminals on the integrated circuit to be tested subject to timing calibration where typically the number of signal terminals is less than the total number of signal terminals on the IC being tested and is typically a relatively small number, e.g., 9. This is useful in the case of high pin count integrated circuits where the pins are grouped into relatively small numbers of pins which are source synchronous. A signal trace electrically connects a different signal terminal to a common reference terminal on each reference block in the set. The reference blocks are then cycled through the tester apparatus as if they were an IC under test, resulting in timing calibration. This allows calibration for critical timing skew requirements for small groups of input/output pins on the IC under test.

Method and apparatus for socket calibration of integrated circuit testers

A method and apparatus for calibrating tester timing accuracy during testing of integrated circuits. An ATE tester measures itself through reference blocks that have the same relevant dimensions as the integrated circuits to be tested. The number of reference blocks required is equal to the number of signal terminals on an integrated circuit to be tested being subject to timing calibration. A signal trace electrically connects a different signal terminal to a common reference terminal on each reference block. Each signal trace used should be closely matched both physically and electrically to the other signal traces used in the set of reference blocks, so that the electrical path length associated with each trace is nearly identical. To perform the timing calibration, the reference blocks may be mounted on a single fixture one at a time, or using multi-site fixtures, multiple reference blocks may be used in parallel. The fixture provides electrical connection of the reference block to the loadboard, and ultimately, the tester.

Growing community of inventors

San Jose, CA, United States of America

Howard Maassen