Fujifilm Corporation

Hirotaka Watano

Haruyasu Nakatsugawa

Kaku Irisawa

Kazuhiro Hirota

Seiichi Inoue

Yoshihiro Seto

Hiroshi Mataki

Taiji Iwasaki

Tatsuyuki Denawa

Takeya Meguro

Yoshihiro Okada

Toshihito Kimura

Fumito Nariyuki

Munetaka Kato

Akira Wakabayashi

Toshiaki Kuniyasu

Toshiyuki Nabeta

Hiroshi Makino

There is provided a biological specimen separation instrument with which a biological specimen can be stably separated into a predetermined component. The biological specimen separation instrument includes an accommodation instrument () that accommodates a collected biological specimen, a filter () for filtering a predetermined component in the biological specimen, and a holding instrument () that accommodates the filtered predetermined component, where the holding instrument is configured to be inserted into the accommodation instrument (), a sealing member () is provided in an outer circumference of the holding instrument () on the tip side in the direction of insertion to to be movable in the accommodation instrument (), in a state of being in liquid-tight contact with an interior wall of the accommodation instrument (), the filter () is held to the holding instrument () by a holder () forming a biological specimen inflow port () to the filter (), and in a case where the filter () and the holding instrument () are cross-sectionally viewed, the sealing member () is positioned on a side opposite to the direction of insertion from an imaginary line () from an end part of the filter (), where the imaginary line () is in contact with a tip side end part (A) on an opposite side across a center of the filter ().

Biological specimen separation instrument

There is provided a biological specimen separation instrument with which a biological specimen can be stably separated into a predetermined component. The biological specimen separation instrument includes an accommodation instrument () for accommodating a collected biological specimen, a filter () for filtering a predetermined component in the collected biological specimen, and a holding instrument () for accommodating the predetermined component filtered by the filter (), where the holding instrument () is configured to be inserted into the accommodation instrument (), in which the filter () is provided on a tip side of the holding instrument () in a direction of insertion into the accommodation instrument (), a sealing member () is provided in an outer circumference on the tip side of the holding instrument () in the direction of insertion to allow movement in the accommodation instrument (), in a state of being liquid-tightly brought into contact with an interior wall of the accommodation instrument (), and the sealing member () has a Shore A hardness of 20 or more and 90 or less and has a residual siloxane concentration of 1 wt % or less.

A management system including at least one processor, wherein the processor is configured to acquire a captured image obtained by imaging an outer surface of each of plural sample containers which contains a sample and in which discrimination information for discriminating a subject from whom the sample is collected is given to the outer surface, and associate a test result related to the sample contained in each of the sample containers with a test order in which information of a discrimination image including the discrimination information is registered in advance for each subject, based on the captured image and the test order.

Management system and management method

A management system including at least one processor, wherein the processor is configured to acquire an image obtained by imaging a sample container containing a sample, recognize relevant information related to reliability of a test result related to the sample based on the image, and derive reliability information indicating the reliability of the test result related to the sample based on the recognized relevant information.

A medicine-holding body is disposed in a flow path of a nozzle portion of an adapter for blood dispensing. The medicine-holding body is formed of a plurality of fibers which is made of polyester and is bundled by aligning a longitudinal direction thereof in a flowing direction which is a direction in which blood flows. The medicine-holding body holds an anticoagulant for suppressing coagulation of blood, as a medicine to be mixed into blood. The surface area of the medicine-holding body is greater than or equal to 10 mmand less than 600 mm. In a case where the surface area of the medicine-holding body is greater than or equal to 10 mm, the concentration of the anticoagulant becomes greater than or equal to a lower limit value of 10 U/mL even under most severe conditions such as a dispensing speed of 500 &#x3bc;L/second. In a case where the surface area of the medicine-holding body is less than 600 mm, it is possible to maintain the occurrence rate of hemolysis to be less than or equal to 10%.

Adapter for blood dispensing

A monocoque-structured housing accommodates a photoelectric conversion panel, a scintillator, and a circuit board in this order from an X-ray incidence side. The scintillator contains cesium iodide and converts X-rays into visible light. The scintillator is vapor-deposited on the photoelectric conversion panel. A plurality of pixels that photoelectrically convert the visible light into charges are formed in the photoelectric conversion panel. A signal processor, which reads out the charge from each pixel and generates image data, is mounted on the circuit board. A gap layer is formed between the scintillator and the circuit board.

Radiographic image detection device

There are provided a method for manufacturing a radiation image detection device, which can cover a scintillator without damaging the scintillator and which can easily form a scintillator protection film with a peripheral portion having a high adhesion to a substrate, and the radiation image detection device. A scintillator protection film that covers a planar scintillator provided on a photoelectric conversion panel is brought into close contact with a scintillator and the photoelectric conversion panel by a planar member having a surface with an irregular shape, and an irregular shape is formed on the scintillator protection film along the irregular shape of the planar member. A distance S between recesses of the irregular shape, the diameter D of the columnar crystal, and the width W of the peripheral portion satisfy the relationship of 'D&#x2266;S&#x2266;W'.

Radiation image detection device and method for manufacturing same

A radiographic image capture device of the present invention includes: a radiation detection panel including a photoelectric conversion element that converts radiation into an electrical signal; a signal processing board that is disposed facing towards the radiation detection panel and that performs signal processing on electrical signals obtained by the radiation detection panel; a flexible substrate that includes wiring lines disposed on a base film provided between the radiation detection panel and the signal processing board and including a low wiring density region and a high wiring density region, and electronic component(s) that are electrically connected to the wiring lines; a reinforcement member that is provided at a low wiring density region and that raises the mechanical strength of the wiring lines.

Radiographic image capture device

A layer-forming apparatus coats a solution containing a layer component and a flammable solvent on a surface of a base material, and forms a layer on the surface of the base material. In the layer-forming apparatus, a coating chamber in which the solution is coated on the surface of the base material is closed substantially hermetically, and a clean air is supplied from a clean-air supplier to the coating chamber. Then, ions that are produced by a corona discharger are sprayed to the surface of the base material in a state that a vapor concentration of the solvent in the coating chamber is below a burning lower limit, and dusts are removed from the base material. Then, the solution is coated on the surface of the base material from which the dusts are removed.

Layer forming method and layer forming apparatus, and method of manufacturing radiation detector

The liquid coating method includes the step of ejecting droplets from nozzles of a recording head onto an imaging region of a surface of a substrate placed on a support plate, wherein a dot pitch &#x3c6; that is an interval between landing positions of the droplets on the surface of the substrate satisfies a following condition: where V stands for a volume of a droplet ejected from each of the nozzles and &#x3b8;stands for an advancing contact angle of the droplet against the substrate.

Growing community of inventors

Ashigarakami-gun, Japan

Hirotaka Watano