Daihen Corporation

Haruhiko Manabe

Toshimitsu Doi

Hirokazu Kawai

Futoshi Nishisaka

Songjie Hou

Keiki Morimoto

Kazutoshi Nagami

Tetsuya Etoh

Hiroyasu Mondori

Hideo Shiozaki

Masayoshi Kureha

Satoru Hata

Hirotsune Tajima

Masahiro Inoue

Hisao Miyahara

Kazuki Yoshida

Hirokazu Ioroi

Kazuhiro Tanaka

Isamu Gamou

Akio Yoshinaga

Takanori Onishi

A power supply system includes multiple power supply devices including a first power supply device and a second power supply device that are connected in common to a load. The first power supply device calculates control information for controlling voltage or current to be output to the load and source information for obtaining the control information, and controls the output to the load based on the calculated control information while transmitting the source information to the second power supply device. The second power supply device receives the source information transmitted from the first power supply device, calculates control information based on the received source information, and controls the output to the load while detecting current to be output from itself to the load and transmitting current information to the first power supply device.

Power supply system, power supply device, and control method

The wire feeding device that feeds welding wire W from the wire source to the welding torch is disposed between the wire source and the welding torch and is configured to temporarily accommodate the welding wire W fed from the wire source and to feed the accommodated welding wire W to the welding torch. In the case where feeding of welding wire W is abnormally stopped, if the acceptance unit accepts instructions for increasing or decreasing, the wire feeding device controls the speed of feeding welding wire W fed by the first feeding part or the second feeding part so that a difference is generated in the feeding speed of the first feeding part and the second feeding part and the accommodated amount of welding wire W is in a range from the lower limit of normal to an upper limit of normal.

Wire feeding device, arc welding device and wire feeding method

A power supply system includes multiple power supply devices including a first power supply device and a second power supply device that are connected in common to a load. The first power supply device calculates control information for controlling voltage or current to be output to the load and controls the output to the load based on the calculated control information while transmitting the control information to the second power supply device. The second power supply device receives the control information and controls the output to the load based on the received control information while detecting current to be output from its own device to the load and transmitting current information to the first power supply device. The first power supply device receives the current information transmitted from the second power supply device and calculates control information based on the received current information and the current and voltage detected by its own device.

A power supply system includes multiple power supply devices connected in common to a load. A first power supply device calculates control information for controlling voltage or current to be output to the load and controls the output to the load based on the calculated control information while transmitting the control information to a second power supply device. The second power supply device receives the control information transmitted from the first power supply device and control the output to the load based on the received control information while detecting current to be output from its own device to the load and transmitting current information to the first power supply device. The first power supply device receives the current information transmitted from the second power supply device and calculate control information based on the received current information and the current and voltage detected by its own device.

Power supply system and power supply device

A power supply device that is applicable to both 200 V and 400 V series input power by switching the operation of an auxiliary switching circuit with a switching switch. When a relatively large output is requested, PWM control is performed to adjust the on pulse width of a control pulse signal provided to switching elements of an inverter circuit and an auxiliary switching circuit, which is operated in cooperation with the inverter circuit. When a relatively small output is requested, PSM control is performed to adjusting a phase difference of two control pulse signals provided to the same set of switching elements in the inverter circuit.

Power supply device and arc machining power supply device

A power supply that performs output PWM control and PSM control. The PWM control is performed when the required output is such that a control signal is set with a larger ON pulse width than a predetermined narrow pulse width allowing for sufficient activation of switching elements in an inverter circuit and an auxiliary switching circuit. The PSM control is performed when the required output is such that the control signal for each switching element is set with a smaller ON pulse width than the predetermined narrow pulse width. The PSM control adjusts the phase of a control pulse signal so that the ON pulse is fixed to the predetermined narrow pulse width.

PWM-PSM controlled power supply with auxiliary switching circuit for soft-switching

A power supply apparatus includes an air path extending longitudinally, a fan that blows air into the air path in a direction intersecting a longitudinal direction of the air path, and a plurality of electronic components arranged in the longitudinal direction. Each of the electronic components is cooled by air passing through the air path. With this configuration, it is possible to efficiently cool the electronic components without compromising the flexibility of arrangement of the various electronic components. Also, a dust removal operation can be readily performed without the possibility of damaging the fan.

Power supply apparatus including fan for air cooling

A power supply for performing arc-machining operation includes a primary rectifier connected to the commercial AC power source and an inverter coupled to the rectifier. A switching device is provided between the rectifier and the inverter. By controlling the power supplied from the rectifier to the inverter, the switching device prevents a large switching loss from occurring in the inverter.

Arc-machining power supply with switching loss reducing element

An inverter power supply system includes a half-bridge inverter circuit which includes a first switching element, a second switching element, a first auxiliary capacitor and a second auxiliary capacitor for converting a DC voltage from a DC power supply circuit to an AC voltage. An output control circuit outputs a first output control signal and a second output control signal with a phase difference of a half cycle to control the inverter circuit. An inverter driving circuit turns on the first (or second) switching element when the first (or second) output control signal turns ON while turning off the first (or second) switching element upon lapse of a first (or second) delay time for allowing the first (or second) auxiliary capacitor to discharge to a predetermined level after the first (or second) output control signal turns OFF.

Growing community of inventors

Osaka, Japan

Haruhiko Manabe