Smart Wires Inc.

Hamed Khalilinia

Haroon Inam

Niloofar Torabi

Amrit Iyer

Antonio Ginart

Michael T Garrison Stuber

Shreesha Adiga Manoor

Govind Chavan

Mahsa Ghapandar Kashani

Adeel Ahmad Khan

Leonard J Kovalsky

Sana Tayyab

Liyu Cao

Zbigniew Wolanski

Leonard Kovalsky

A clamping circuit employs a filter comprising two series branches of surge arresting circuits to clamp voltage spikes on equipment in series with a power transmission line. Clamping of these voltage spikes protects insulators, semiconductors, and other sensitive components within the series equipment from transient grid events. By using a predetermined frequency to control the response, the filter does not interfere with normal operation of the power system nor the operation of a power flow control module series-coupled to the transmission line through the filter. The clamping circuit employs hysteresis and imposes a shared voltage ratio between the two circuit branches, the ratio depending on frequency and voltage of the transient asserted on the transmission line, in order to provide a very sharp protection response to events within the target frequency range.

Clamping circuit for protecting FACTs

A fault detection system has line current monitors. Each line current monitor couples to a line-phase of an electric power transmission system. Each line current monitor has a phase detector, a loop filter and a controlled oscillator, coupled as a phase locked loop. The phase detector has a rotating frame transform. The phase detector couples to a line-phase and provides in-phase and quadrature signals in a rotating frame, based on in-phase and quadrature signals proportional to current in the line-phase. One or more fault detection modules are coupled to the line current monitors through inter-phase communication of the in-phase and quadrature signals in a time frame rotating at the line frequency. The communication may have electrical isolation.

Method and apparatus for detecting faults using current unbalance

Disclosed is a reactance-injecting module and its method of use to balance the currents among the phases of polyphase electric power transmission lines or to manage power flow among alternate paths, where the reactance-injecting module has high-speed, dedicated communication links to enable the immediate removal or reduction of injected reactance from all phases of a phase balancing cluster when a fault is detected on any one of the multiple phases. The reactance-injecting module may communicate information on a detected fault to the other reactance-injecting modules of the phase balancing cluster within 10 microseconds after the fault is detected to allow the phase balancing cluster to eliminate injected reactance from all phases within a time that is short compared to a cycle of the alternating current, such as 1 millisecond after the fault is detected. This provides extremely fast neutralization of injected reactance to minimize interference with fault localization analyses.

Fast post-fault phase reactance balancing

A filter network is insertable into a power transmission line, to handle disturbances in the power transmission line. A first circuit has an RC network in parallel with a surge arrestor, to bypass high frequency disturbances of the power transmission line. A second circuit has inductors for carrying low-frequency power to and from impedance injection units.

Protection from and filtering of disturbances for serial connected facts

The presence of injected DC has harmful consequences for a power grid system. A piecewise sinusoidal ripple voltage wave at the line-frequency that rides on the main capacitor bank of the power converter is observed. This observation leads to a new detection method and mitigation method. A two-stage control circuit is added to the operation of a power converter that controls power line impedance in order to mitigate the injected DC and to block DC circulation. This control computes a correction angle to adjust the timing of generated pulsed square waves to counter-balance the ripple. A functional solution and the results of experiments are presented. Furthermore, an extraction method and three elimination methods for this ripple component are presented to allow dissipation of DC energy through heat and/or electronic magnetic wave, or to allow transformation of this energy into usable power that is fed back into the power grid.

Detection and mitigation of DC injection on the power grid system

The presence of injected DC has harmful consequences for a power grid system. A piecewise sinusoidal ripple voltage wave at the line-frequency that rides on the main capacitor bank of the power converter is observed. This observation leads to a new DC detection elimination method. Three DC elimination methods for this ripple component are disclosed to allow dissipation of DC energy through heat and/or electromagnetic wave, or to allow transformation of this energy into usable power that is fed back into the power grid.

Detection and elimination of DC injection on the power grid system

Disclosed is a reactance-injecting module used to balance the currents among the phases of polyphase electric power transmission lines or to manage power flow among alternate paths, where the reactance-injecting module has high-speed, dedicated communication links to enable the immediate removal of injected reactance from all phases of a phase balancing cluster when a fault is detected on any one of the multiple phases. The reactance-injecting module may communicate information on a detected fault to the other reactance-injecting modules of the phase balancing cluster within 10 microseconds after the fault is detected to allow the phase balancing cluster to eliminate injected reactance from all phases within 1 millisecond after the fault is detected. This provides extremely fast neutralization of injected reactance to minimize interference with fault localization analyses.

A modular power flow control system having early detection and reporting of transmission line faults is described. The response time for closing a bypass switch and reporting the fault is less than 200 microseconds for hard faults, longer for soft faults. Reprogramming of distance relays is not required. Transmission line faults are characterized using a fault detection sensor suite, normally including at least a current sensor such as a current transformer and a rate of current change sensor such as a Rogowski coil, and in some embodiments, a temperature sensor. Other embodiments are disclosed.

Growing community of inventors

Hayward, CA, United States of America

Hamed Khalilinia