Dialog Semiconductor Gmbh

Guang Feng

Xiaoyan Wang

Nan Shi

Pengju Kong

Clarita Chiting Knoll

Qiu Sha

Chuanyang Wang

Jianming Yao

Liang Yan

Clarita C Poon

Chenglong Zhang

Qifeng Shi

Yong Xiong Lin

Jiang Yu

John William Kesterson

Kai-Wen Chin

Juyoung Yoon

Haiju Li

Mingsheng Peng

David H Nguyen

Andrey B Malinin

Dickson T Wong

Tao Li

Yimin Chen

Xiaolin Gao

Jiang Chen

Mengfei Liu

Qingqing Zong

Xiyuan Liu

Clarita Poon

Chuangyang Wang

A flyback converter is provided that includes a high-side synchronous rectifier switch transistor. A secondary-side synchronous rectifier controller powered by a power supply voltage controls a cycling on and off of the high-side synchronous rectifier switch transistor. An active control of the charging of the power supply voltage uses an auxiliary capacitor that is charged from a charge source while a power switch transistor in a first switching state. When the power switch transistor is in a second switching state that is the complement of the first switching state, the active control coupes the auxiliary capacitor to a power supply capacitor that stores the power supply voltage.

High-side synchronous rectifier driver with reduced controller power supply charging efficiency and reduced EMI

A flyback converter is provided that detects a load-transient-produced increase in the output current to more quickly detect and respond to the load transient.

Flyback converter with fast load transient detection

An isolated switching power converter having a primary-side and secondary-side in signal communication with an input and an output is disclosed. The isolated switching power converter comprises a transformer, primary-side switch, secondary-side switch, primary-side controller, and secondary-side controller. The transformer includes a primary-winding and a secondary-winding in signal communication with the input and output. The primary-side switch is in signal communication with the primary-winding and the secondary-side switch is in signal communication with the secondary-winding. The primary-side controller is on the primary-side and the secondary-side controller is on the secondary-side. The primary-side controller is configured to output a control signal for operating the primary-side switch and the secondary-side controller configured to monitor a voltage across the secondary-side switch, output a control signal for switching the secondary-side switch, and turn-off the secondary-side switch at an off-time of the primary-side switch to transmit a data signal to the primary-side controller.

Isolated switching power converter with data communication between primary and secondary sides

A switching power supply controller for a switching power supply is provided that measures an input voltage through an application of a load during an input voltage measurement period following connection of the switching power supply to an AC mains. Based upon the measured input voltage, the controller adjusts a start-up delay period so that the start-up delay period is substantially constant despite variations in an AC line voltage for the AC mains.

Adaptive startup for switching power converter

Systems, devices, and methods are provided to enable power converters to use two or more sensing elements to reliably detect a short circuit (or soft-short circuit) existing in the power converter and distinguish these conditions from other operating conditions, such as low voltage conditions or normal operating conditions. The disclosed embodiments enable the accurate detection of fault conditions, such as short circuits or soft short conditions, using a number of sensing elements, such as sense resistors and the inherent resistance of switching devices, while preventing the detection of false positives due to other factors such as low input voltage.

Sense resistor short detection for switching power converters

A flyback converter controller is provided with a single terminal through which the flyback converter controller senses for over-voltage faults for an input voltage and also senses for open circuit faults for an auxiliary winding. A first voltage divider provides a divided version of the input voltage to the single terminal. The controller compares a voltage for the single terminal to at least one over-voltage threshold to detect the over-voltage fault for the input voltage.

Flyback converter controller with single pin detection of over-voltage and auxiliary winding faults

A single configuration terminal of a device is used to configure multiple operating parameters of the device based on a resistor and a capacitor selectively connected to the configuration terminal. The device includes a detection circuit configured to monitor a voltage signal at the configuration terminal to determine multiple values in response to a regulated current source providing a current to the configuration terminal selectively connected to the resistor and the capacitor in parallel, and configure multiple operating parameters based on the determined values. A method for configuring operating parameters using a single configuration terminal of a device includes providing a current to the configuration terminal selectively connected to a resistor and a capacitor in parallel, monitoring a voltage signal at the configuration terminal, determining multiple values based on the monitoring, and configuring multiple operating parameter based on the determined values.

Selection of multiple configuration settings using a single configuration terminal

A controller for a switching power converter is provided with a single detection pin through which the controller monitors whether the switching power converter is connected to an AC mains. Should a voltage for the detection pin indicate that the switching power converter is disconnected from the AC mains, the controller asserts the detection pin voltage to trigger a bleeder circuit to discharge an X class capacitor.

AC line detection and X capacitor discharge using a single terminal

A switching power converter is provided that uses at least two peak current thresholds. In particular, the switching power converter clamps a desired peak current to not fall below a low peak current threshold value while a rectified input voltage is decreasing and to not fall below a high peak current threshold value subsequent to zero crossing times for an AC input voltage.

Switching power converter with magnetizing current shaping

A power switch transistor for a switching power converter is maintained on during a re-startup period by a zener breakdown voltage following a fault condition for the switching power converter. A source voltage from the power switch transistor is used to charge a VCC capacitor that stores a power supply voltage for a controller for the switching power converter.

Active startup timing control at fault mode

A startup circuit is provided for establishing the Vcc voltage level of a switching power converter. The startup circuit uses a switch controller and path switching transistor to provide a two-stage Vcc capacitor charging that reduces startup time while avoiding short circuit damage through the alternate usage of a high impedance charging path and a low-impedance charging path.

Dual stage Vcc charging for switched mode power supply

A multi-mode control scheme for an LED lamp system uses the detected firing angle of an AC input voltage waveform to select from multiple regulation modes. In operation, a current controller compares the detected firing angle to one or more specified thresholds and selects the appropriate regulation scheme based on the comparison result. When the detected firing angle is less than a first firing angle threshold, the controller employs a current shaping regulation mode. When the detected firing angle is greater than a second firing angle threshold, the controller employs a switching cycle-I Peak modulation regulation mode. And when the detected firing angle is greater than the first firing angle threshold and less than the second firing angle threshold, the controller employs a hybrid regulation mode.

Multi-mode control for solid state lighting

An LED lamp comprises one or more LEDs and an LED driver receiving an input signal from a dimmer switch indicative of an amount of dimming for the LED lamp. The LED driver controls regulated current through the one or more LEDs based on the input signal such that an output light intensity of the one or more LEDs substantially corresponds to the amount of dimming for the LED lamp. A regulated output provides operating power for the LED driver. A controller regulates the regulated output to power the LED driver. The controller selects a power source for charging the regulated output from two or more power sources, and the regulated output is charged using the power source selected by the controller.

Powering internal components of LED lamps using dissipative sources

Intelligent control of a solid state lamp when coupled to a trailing edge phase cut dimmer switch is provided. On and off cycles of the lamp's power stage switch are enabled during a period when the energy in the bulk capacitor is at its highest levels. During this period a bleeder circuit does not have to be enabled, which results in a greater operational efficiency as compared with normal switching schemes for trailing edge dimmers.

Growing community of inventors

Cupertino, CA, United States of America

Guang Feng