Rca Licensing Corporation

Rca Inc.

Giovanni M Leonardi

Willem Den Hollander

In a switch mode power supply, a first switching transistor is coupled to a primary winding of an isolation transformer. A second switching transistor periodically applies a low impedance across a second winding of the transformer that is coupled to an oscillator for synchronizing the oscillator to the horizontal frequency. A third winding of the transformer is coupled via a switching diode to a capacitor of a control circuit for developing a DC control voltage in the capacitor that varies in accordance with a supply voltage B+. The control voltage is applied via the transformer to a pulse width modulator that is responsive to the oscillator output signal for producing a pulse-width modulated control signal. The control signal is applied to a mains coupled chopper transistor for generating and regulating the supply voltage B+ in accordance with the pulse width modulation of the control signal.

Synchronized switch-mode power supply

In a switch mode power supply, a first switching transistor is coupled to a primary winding of a transformer for generating pulses of a switching current. A secondary winding of the transformer is coupled via a switching diode to a capacitor of a control circuit for developing a control signal in the capacitor. The control signal is applied to a mains coupled chopper second transistor for generating and regulating supply voltages in accordance with pulse width modulation of the control signal. During standby operation, the first and second transistors operate in a burst mode that is repetitive at a frequency of the AC mains supply voltage such as 50 Hz. In the burst mode operation, during intervals in which pulses of the switching current occur, the pulse width and peak amplitude of the switching current pulses progressively increase in accordance with the waveform of the mains supply voltage to provide a soft start operation in the standby mode of operation within each burst group.

Switch-mode power supply with burst mode standby operation

In a switch mode power supply, a first switching transistor is coupled to a primary winding of an isolation transformer. A secondary winding of the transformer is coupled via a switching diode to a capacitor of a control circuit for developing a DC control voltage in the capacitor. The DC level of the control voltage varies in accordance with a supply voltage B+. A change in voltage B+ produces a corresponding, greater change in the control voltage. The control voltage is applied to the transformer when the diode is conducting for producing a pulse-width modulated control signal. The control signal is applied to a mains coupled chopper transistor for generating and regulating the supply voltage B+ in accordance with the pulse width modulation of the control signal.

Switch-mode power supply with transformer-coupled feedback

An input supply voltage is coupled via a primary winding of a flyback transformer to a collector of a chopper transistor switch that operates at a given frequency. During a portion of each period when the chopper transistor switch is conductive, a second switch applies a short-circuit across a secondary winding of the transformer at a controllable instant that causes the emitter current of the chopper transistor switch to increase at a significantly higher rate. When the emitter current exceeds a predetermined threshold level, a one-shot arrangement is triggered. Consequently, a pulse is produced that turns off the chopper transistor switch and that maintains it nonconductive for the duration of the pulse. A flyback pulse produced in a winding of the transformer is rectified to produce a DC output supply voltage. The length of the interval when the chopper transistor switch is conductive is controlled by the second switch in accordance with the level of the output supply voltage in a negative feedback manner for regulating the output supply voltage.

Switch-mode power supply

A vertical deflection current generator includes an operational amplifier responsive to an input sawtooth signal at a vertical rate. A first end terminal of a deflection winding is coupled to an output terminal of the amplifier. A second end terminal of the deflection winding is coupled in series with a parallel arrangement of a switch and a capacitor. The switch is conductive during vertical trace. During vertical retrace, the switch is nonconductive that causes a vertical retrace voltage to develop in a flyback manner in the retrace capacitor. The retrace voltage in the retrace capacitor and a retrace voltage at the output terminal of the amplifier that are opposite in phase speed up the reversal of a deflection current in the deflection winding.

Vertical deflection current generator

A gullwing distortion correction signal and a north-south pincushion distortion correction signal are generated and then summed to form a sum signal. The sum signal is coupled to a primary winding of a transformer. A secondary winding of the transformer is coupled in a current path of a vertical rate deflection current for modulating the deflection current in a manner that reduces the gullwing and north-south pincushion distortions. The secondary winding is included in a resonant circuit that is tuned to resonate at the horizontal frequency.

Gullwing distortion correction circuit

The field rate of a video input signal is doubled by storing each field in a memory and recovering each stored fields twice so as to repeat each field and thus reduce flicker. To ensure that even fields overlay even fields, odd fields overlay odd fields and that all pairs of even and odd fields are interlaced, a timing unit provides a double field rate read control signal to the memory having a waveform that repeats on a two-field basis and supplies a double field rate vertical control signal to a vertical deflection generator having a waveform that is phase modulated and that repeats on a four-field basis. The vertical deflection generator has a constant retrace time and employs DC coupling, thereby avoiding raster shift which otherwise could occur as a result of the phase modulation.

Television apparatus for generating a phase modulated deflection current

The field rate of a video input signal is doubled by storing each field in a memory and recovering each stored fields twice so as to repeat each field and thus reduce flicker. To ensure that even fields overlay even fields, odd fields overly odd fields and that all pairs of even and odd fields are interlaced, a timing unit provides a double field rate control signal to the memory having a waveform that repeats on a two-field basis and supplies a double field rate vertical synchronizing signal to a display having a waveform that repeats on a four-field basis. Registration of images is enhanced further by means of a vertical scan generator having a constant retrace time, a fixed retrace level and employing DC coupling thereby avoiding raster shift which otherwise could occur as a result of the use of non-equidistant vertical synchronizing pulses.

Growing community of inventors

Zurich, Switzerland

Giovanni M Leonardi