Massachusetts Institute of Technology

Barrett Technology, Inc.

Solectria Corporation

Burnside Acquisition, LLC

Energid Technologies Corporation

Permabit, Inc.

Subscriber Solutions, Inc.

Gill A Pratt

Hugh Miller Herr

Joaquin Blaya

Norman H Margolus

John N Nguyen

Stephen A Ward

Adam Crowell

Traveler Hauptman

Thomas F Knight, Jr

Michael Brian Wittig

William T Townsend

Bruce Wayne Deffenbaugh

John S Pezaris

Matthew M Williamson

David W Robinson

Jeff Anthony Weber

Roderick T Hinman

James D Worden

Jianjuen Hu

Ricardo Espinosa

William T Townsendl

David Reed

An Active Ankle Foot Orthosis (AAFO) is provided where the impedance of an orthotic joint is modulated throughout the walking cycle to treat ankle foot gait pathology, such as drop foot gait. During controlled plantar flexion, a biomimetic torsional spring control is applied where orthotic joint stiffness is actively adjusted to minimize forefoot collisions with the ground. Throughout late stance, joint impedance is minimized so as not to impede powered plantar flexion movements, and during the swing phase, a torsional spring-damper (PD) control lifts the foot to provide toe clearance. To assess the clinical effects of variable-impedance control, kinetic and kinematic gait data were collected on two drop foot participants wearing the AAFO. It has been found that actively adjusting joint impedance reduces the occurrence of slap foot, allows greater powered plantar flexion, and provides for less kinematic difference during swing when compared to normals.

Motorized limb assistance device

Active ankle foot orthosis

A haptic simulation method determines a location of a needle assembly within a magneto-rheological fluid. The needle assembly within the magneto-rheological fluid is associated with a desired resistance value. A viscosity control signal representative of the desired resistance value is generated. The viscosity control signal is applied to a viscosity control device to vary a viscosity of the magneto-rheological fluid to achieve the desired resistance value.

Method and apparatus for haptic simulation

The present invention relates to a variable-torque magnetorheologically actuated prosthetic knee which utilizes a plurality of interspersed and alternating rotors and stators to shear magnetorheological fluid in gaps formed therebetween. Advantageously, by operating in the 'shear mode' there is substantially no or negligible fluid pressure buildup or change. Moreover, the multiple MR fluid gaps or flux interfaces desirably allow for the production of a large torque at low speed&#x2014;eliminating the need for a transmission&#x2014;and also for a wide dynamic torque range. One embodiment of the invention allows the rotors and/or stators to close the gaps therebetween to create a frictional torque component, thereby forming a 'hybrid' braking system which provides a total torque or damping which is a combination of viscous torque and frictional torque.

Electronically controlled prosthetic knee

Featured is a controller for a motor that is ultra-compact, with a power density of at least about 20 watts per cubic cm (W/cm). The controller utilizes a common ground for power circuitry, which energizes the windings of the motor, and the signal circuitry, which controls this energization responsive to signals from one or more sensors. Also, the ground is held at a stable potential without galvanic isolation. The circuits, their components and connectors are sized and located to minimize their inductance and heat is dissipated by conduction to the controller's exterior such as by a thermally conductive and electrically insulating material (e.g., potable epoxy). The controller uses a single current sensor for plural windings and preferably a single heat sensor within the controller. The body of the controller can also function as the sole plug connector.

Ultra-compact, high-performance motor controller and method of using same

Ultra-compact, high-performance motor controller

A method and apparatus are provided for dynamically routing a plurality of simultaneous point-to-point communications through an array of repeating transceivers. Each repeating transceiver may simultaneously act as each of a transmitter of origin for one communication, a final receiver for a second communication, and a repeater for a plurality of other communications. When acting as a repeater, each transceiver applies programmed delays to information before re-transmitting, and these delays are programmed so as to route a communication through the array of transceivers along a designed path along which multiple re-transmissions from local repeating transceivers are received, aligned in time for constructive reinforcement, and retransmitted after dynamically programmable time delays.

Delay based space and time coordinated repeater system

In general, the invention features methods by which more than one client program connected to a network stores the same data item on a storage device of a data repository connected to the network. In one aspect, the method comprises encrypting the data item using a key derived from the content of the data item, determining a digital fingerprint of the data item, and storing the data item on the storage device at a location or locations associated with the digital fingerprint. In a second aspect, the method comprises determining a digital fingerprint of the data item, testing for whether the data item is already stored in the repository by comparing the digital fingerprint of the data item to the digital fingerprints of data items already in storage in the repository, and challenging a client that is attempting to deposit a data item already stored in the repository, to ascertain that the client has the full data item.

Data repository and method for promoting network storage of data

Growing community of inventors

Lexington, MA, United States of America

Gill A Pratt