Ericsson Gmbh

Smartsky Networks, LLC

Sony Ericsson Mobile Communications Ab

Telefonaktiebolaget Lm Ericsson (publ)

North Carolina State University

Sony Mobile Communications Ab

Sony Corporation

Other

Ericcson Inc.

Gerard James Hayes

Koichiro Takamizawa

Elbert Stanford Eskridge, Jr

Robert A Sadler

Curtis W Thornton

Howard Eugene Holshouser

Ross Warren Lampe

Brian Francis Mellage

James O Legvold

Douglas A Hyslop

Scott Ladell Vance

James D MacDonald, Jr

John Michael Spall

John Swartz

Mike Barts

Kim Rutkowski

Russell Evans Winstead

Mark Gordon Douglas

Charles Albert Rudisill

Michael David Dickey

Gianluca Lazzi

Huan-sheng Hwang

Joe Klein

Ronald A Louks

Ju-Hee So

Jacob Thelen

Amit Qusba

Walter M Marcinkiewicz

Donald L Alcorn

Nadi Sakir Findikli

Bruce J Holmes

Mohammod Ali

Robert Michael Barts

Michael D Doub

James Evans Ladd, Jr

Stefan Schmidt

Peter Dimitrios Karabinis

William O Camp, Jr

Nils Rutger Rydbeck

David Ryan Story

Charles Curtiss Hunt

Rodney Owen Williams

Seung Kil Kim

Paul Leonard Futter

Rodney A Dolman

Scott LaDell Vance

Yawei Ma

Bruce Emerson Wilcox

Robert Ray Horton

John Thomas Sadler

John Weldon Gammon

Lee Daniel Griffin

Craig A Phelps

Michael D Townsend

William Paul Stewart

James O Legvoid

Rodney O Williams

Minh Chau Huynh

Jr Elbert Eskridge

Jr Elbert Stanford Eskridge

Curtis Wayne Thornton

Jr William O Camp

Paul Futter

Patrik Lilja

A base station within a network for providing ATG wireless communication in various cells may include an antenna array defining a plurality of wedge shaped sectors having respective widths defined in azimuth, and a beamforming control module. The beamforming control module may be configured to communicate with the antenna array via a first RF chain to perform beamforming defining traffic channel beams having a first width, and a second RF chain to perform beamforming defining control channel beams having a second width. The second width may be greater than the first width.

Air to ground communication system with separate control and traffic channels

A global positioning system (GPS) receiver may include an antenna configured to receive GPS signals from GPS satellites, a radio frequency (RF) front end configured to pre-process signals received by the antenna, a demodulator/converter configured to perform demodulation and analog-to-digital conversion of output signals received from the RF front end, a clock configured to provide a consistent clock signal, and a digital signal processor configured to receive the clock signal and make time and code measurements associated with determining a location of the GPS receiver based on the signals received by the antenna. The GPS receiver may be configured to eliminate reflected or indirect signals from the time and code measurements.

Optimized position information assisted beamforming

A unified radio system for providing wireless communication to a communication device on an aircraft regardless of aircraft altitude may include a terrestrial network including a plurality of terrestrial base stations configured to communicate primarily in a ground communication layer below a first altitude, an ATG network including a plurality of ATG base stations configured to communicate primarily in an ATG communication layer above a second altitude, an air-to-air mesh network for data relays through connected aircraft, and an aircraft with an onboard antenna assembly and a unified radio. The unified radio may be configured to monitor network parameters of the terrestrial network and the ATG network and switch between a currently serving network and a non-serving network based on the network parameters.

Unified radio solution

An antenna assembly includes a plurality of active antenna elements disposed in a first linear array along a reference line and equidistant from each adjacent antenna element by a first linear distance, and a plurality of passive antenna elements disposed in a second linear array extending parallel to the reference line such that each passive antenna element is a second linear distance away from a corresponding one of the active antenna elements. The antenna assembly includes or is operably coupled to a phase control module configured to apply selected phase fronts to selected ones of the antenna elements to generate constructive and destructive interference patterns to define a directive beam in a desired direction in a range between about 0 and 180 degrees relative to the reference line.

Digital beamforming fin antenna assembly

An antenna assembly includes a plurality of antenna elements disposed in a circular pattern and equidistant from each other in angular separation relative to a common reference point at a center of the circular pattern. The antenna assembly may include or be operably coupled to a phase control module configured to apply selected phase fronts to each of the antenna elements to generate constructive and destructive interference patterns to define a directive beam in a desired direction. The selected phase fronts may include no phase adjustment, a positive phase adjustment value and a negative phase adjustment value, the positive and negative phase adjustment values each having a same magnitude.

Directive beamforming antenna

A network controller including processing circuitry may be configured to receive dynamic position information indicative of a three dimensional position of at least one mobile communication node, compare fixed position information indicative of fixed geographic locations of respective access points of a network to the dynamic position information to determine a relative position of the at least one mobile communication node relative to at least one of the access points based on the fixed position information and the dynamic position information, and provide network control instructions to at least one network asset based on the relative position.

Position information assisted network control

A method of interference mitigation may include receiving a desired signal from an asset of the system at an antenna assembly and associating the desired signal with relative phase distribution information based on a relative location of origin of the desired signal where the relative phase distribution information is predetermined for the antenna assembly. The method further includes receiving an interfering signal and associating the interfering signal with relative phase distribution information based on a relative location of origin of the interfering signal where the desired signal and the interfering signal forming a received signal set. The method further includes normalizing signals of the received signal set to respective relative phases associated with each respective relative location of origin, and performing interference cancellation of the interfering signal based on the normalized signals.

Interference mitigation based on antenna system phase distribution

An antenna assembly includes a driven element, a first set of antenna elements disposed a first distance from the driven element such that each element of the first set of antenna elements is equidistant from adjacent elements of the first set of antenna elements, and a second set of antenna elements disposed a second distance from the driven element such that each element of the second set of antenna elements is equidistant from adjacent elements of the second set of antenna elements, the second distance being larger than the first distance. The antenna assembly includes or is operably coupled to a selector module configured to select one element of the first set of antenna elements as a selected director, and select one element of the second set of antenna elements as a selected reflector by effectively shortening a length of the selected director and effectively lengthening the selected reflector.

Monopole antenna assembly with directive-reflective control

An antenna assembly may include an antenna element, a radome structure disposed proximate to the antenna element and including a plurality of plasma elements, a driver circuit operably coupled to the plasma elements to selectively ionize individual ones of the plasma elements, and a controller. The controller may be operably coupled to the driver circuit to provide control of plasma density of the individual ones of the plasma elements. The plasma elements may include respective enclosures. At least some of the enclosures may have at least two peripheral edge surfaces substantially fully contacted by corresponding peripheral edge surfaces of adjacent enclosures at at least one section along a longitudinal length thereof.

Plasma radome with flexible density control

A method of enhancing wireless communication performance includes receiving information indicative of a local interferer where the local interferer is identified based on dynamic position information indicative of a position of at least one mobile communication node, performing noise cancellation relative to a received signal by removing an interference signal associated with the local interferer to generate a scrubbed signal, and providing the scrubbed signal for additional signal processing.

Spectrum scrubber

Growing community of inventors

Wake Forest, NC, United States of America

Gerard James Hayes