Sgs-thomson Microelectronics Limited

Stmicroelectronics Gmbh

Fu-Tai Liou

Fusen E Chen

Yih-Shung Lin

Che-Chia Wei

Girish A Dixit

Charles R Spinner, Iii

Yu-Pin Han

Frank R Bryant

Mehdi Zamanian

Robert O Miller

Timothy E Turner

John L Walters

Lun-Tseng Lu

Mohammed M Farohani

Tsiu Chiu Chan

Robert L Hodges

Fusen F Chen

Charles Ralph Spinner

Frank F Bryant

A method for fabricating interlevel contacts in semiconductor integrated circuits provides for formation of a contact opening through an insulating layer. A layer of refractory metal, or refractory metal alloy, is deposited over the surface of the integrated circuit chip. An aluminum layer is then deposited at a significantly elevated temperature, so that an aluminum/refractory metal alloy is formed at the interface between the aluminum layer and the refractory metal layer. Formation of such an alloy causes an expansion of the metal within the contact opening, thereby filling the contact opening and providing a smooth upper contour to the deposited aluminum layer.

Method for fabricating interlevel contacts of aluminum/refractory metal alloys

A contact opening through an insulating layer is filled with metal and etched back to form a metal plug within the opening. A metal interconnect line can then be formed over the contact, and makes electrical contact with the metal plug. Since the contact opening is filled by the metal plug, it is not necessary for the metal signal line to have a widened portion in order to ensure enclosure.

Semiconductor contact via structure and method

A method for forming an aluminum contact through an insulating layer includes the formation of an opening. A barrier layer is formed, if necessary, over the insulating layer and in the opening. A thin refractory metal layer is then formed over the barrier layer, and aluminum deposited over the refractory metal layer. Proper selection of the refractory metal layer and aluminum deposition conditions allows the aluminum to flow into the contact and completely fill it. Preferably, the aluminum is deposited over the refractory metal layer without breaking vacuum.

Aluminum contact structure for integrated circuits

A method is provided for depositing aluminum thin film layers to form contacts in a semiconductor integrated circuit device. All or some of the deposition process occurs at relatively low deposition rates at a temperature which allows surface migration of the deposited aluminum atoms. Aluminum deposited under these conditions tends to fill contact vias without the formation of voids. The deposition step is periodically interrupted.

Method for forming a metal contact

A method is provided for forming improved quality interlevel aluminum contacts in semiconductor integrated circuits. A contact opening is formed through an insulating layer. A barrier layer is deposited over the surface of the integrated circuit. An aluminum layer is then deposited at relatively low deposition rates at a temperature which allows improved surface migration of the deposited aluminum atoms. Aluminum deposited under these conditions tends to fill contact vias without the formation of voids. The low temperature deposition step can be initiated by depositing aluminum while a wafer containing the integrated circuit device is being heated from cooler temperatures within the deposition chamber.

Method of producing an aluminum stacked contact/via for multilayer

Interlevel contacts in semiconductor integrated circuits are fabricated by formation of a contact opening through an insulating layer. A layer of refractory metal, or refractory metal alloy, is deposited over the surface of the integrated circuit chip. An aluminum layer is then deposited at a significantly elevated temperature, so that an aluminum/refractory metal alloy is formed at the interface between the aluminum layer and the refractory metal layer. Formation of such an alloy causes an expansion of the metal within the contact opening, thereby filling the contact opening and providing a smooth upper contour to the deposited aluminum layer.

Interlevel contact including aluminum-refractory metal alloy formed during aluminum deposition at an elevated temperature

A method is provided of forming a small geometry via or contact of a semiconductor integrated circuit, and an integrated circuit formed according to the same, is disclosed. According to a first disclosed embodiment, an opening is formed partially through an insulating layer overlying a conductive region. Sidewall spacers are formed along the sidewalls of the opening. The remaining insulating layer is etched to expose the underlying conductive region. The contact dimension of the opening is smaller than the opening which can be printed from modern photolithography techniques. According to an alternate embodiment, the opening in the insulating layer expose the underlying conductive region. A polysilicon layer is formed over the insulating layer and in the opening. The polysilicon is oxidized to form a thick oxide in the opening and is etched back to form oxidized polysilicon sidewall spacers which decrease the contact dimension of the opening. According to a further alternate embodiment, an etch stop layer is formed between the insulating layer and conductive region and an opening is formed in the insulating layer exposing the etch stop layer. A sidewall spacer film is formed over the insulating layer and the etch stop layer, both layers having a similar etch rate for a given etchant. The etch stop and spacer layers are etched in the opening to expose the underlying conductive layer thereby forming a contiguous sidewall spacer and etch stop layer on the sides of and under the insulating layer, thereby decreasing the contact dimension of the opening.

Method of forming submicron contacts and vias in an integrated circuit

Method for forming an aluminum contact

A method is provided for depositing aluminum thin film layers to form contacts in a semiconductor integrated circuit device. All or some of the deposition process occurs at relatively low deposition rates at a temperature which allows improved surface migration of the deposited aluminum atoms. Aluminum deposited under these conditions tends to fill contact vias without the formation of voids. The low temperature deposition step can be initiated by depositing aluminum while a wafer containing the integrated circuit device is being heated from cooler temperatures within the deposition chamber.

A method for fabrication of metal to semiconductor contacts results in sloped sidewalls in contact regions. An oxide layer is deposited and etched back to form sidewall spacers. A glass layer is then deposited and heated to reflow. After reflow, an etch back of the glass layer results is sloped sidewalls at contact openings and over steps.

Contacts for semiconductor devices

A method is provided for forming a contact opening or via of a semiconductor integrated circuit, and an integrated circuit formed according to the same. A first metal region is formed over an underlying region. A first insulating layer is formed over the integrated circuit. A second insulating layer is then formed over the first insulating layer. A portion of the second insulating layer is etched to expose a portion of the first insulating layer wherein the exposed first insulating layer and the remaining second insulating layer form a substantially planar surface. A metal oxide layer is formed over the exposed first insulating layer and the remaining second insulating layer. A photoresist layer is formed and patterned over the metal oxide layer. The metal oxide layer is then selectively etched to form a via exposing a portion of the first insulating layer. The first insulating layer in the via is then selectively etched to expose a portion of the first metal region. The photoresist layer is removed and a second metal layer is then formed over the metal oxide layer and in the via contacting the first metal region.

Structure and method of forming vias

Submicron contacts and vias in an integrated circuit

A method is provided for forming contact via in an integrated circuit. Initially, a first buffer layer is formed over an insulating layer in an integrated circuit. The first buffer layer has a different etch rate from the insulating layer. A second buffer layer is then formed over the first buffer layer, with the second buffer layer having an etch rate which is faster than the first buffer layer. An isotropic etch is performed to create an opening through the second buffer layer and a portion of the first buffer layer. Because the second buffer layer etches faster than the first buffer layer, the slant of the sideswalls of the opening can be controlled. An anisotropic etch is then performed to complete formation of the contact via.

Growing community of inventors

Carrollton, TX, United States of America

Fu-Tai Liou