Robert Boschgmbh

Friedrich Moser

Guenther Hohl

Thomas Kuegler

Olaf Schoenrock

Maike Sander-Potz

Peter Boehland

Juergen Graner

Michael Knorpp

Christoph Buehler

Gerhard Mack

Joachim Winter

Wendelin Potz

Philippe Allio

Klaus Schudt

Michael U Fischer

Philipp Rogler

Christof Ott

Matthias Schumacher

Anselm Berg

Markus Friedrich

Jochen Rager

Wilhelm Christ

Markus Gesk

Walter Maeurer

Andreas Burghardt

Andreas Koeninger

Johannes Schmid

Tilla Haubold

Volker Sohm

Predrag Nunic

Hirokazu Terashima

Sven Krissler

Thilo Kreher

Markus Krasemann

Horst Opielka

Guenther Kubalik

Kerstin Kling

Herbert Hoelzl

A gas injector for injecting a gaseous fuel directly into a combustion chamber of an internal combustion engine, having a valve closing element for releasing and closing a through-opening, a first seal seat between the valve closing element and a valve body, the first seal seat being a metallic seal seat having two metallic sealing partners, and having a second seal seat between the valve closing element and a stationary component, the second seal seat having at least one elastomer seal as sealing partner, the first seal seat being situated closer to the combustion chamber than is the second seal seat.

Direct injection gas injector with an elastomer seal

A gas injector for injecting a gaseous fuel, in particular directly into a combustion chamber of an internal combustion engine, including: a valve closing element for opening or closing a pass-through opening, a valve body, and a sealing seat between the valve body and the valve closing element, in the case of a maximum lift of the valve closing element a flow cross section between the valve body and the valve closing element being smaller in the flow direction upstream from the sealing seat than a flow cross section between the valve closing element and the sealing seat and being smaller than a flow cross section in the flow direction downstream from the sealing seat.

Gas injector including lift dethrottling

A method for manufacturing a pole tube having two magnetic pole tube components and having one nonmagnetic ring, which is situated axially between the pole tube components, for an electromagnet, in particular for a solenoid valve of an automatic transmission in a motor vehicle, including the following: concentric configuration and/or centering of the pole tube components and of the ring, in particular on a centering pin; form-fitting connection, in particular by extrusion coating and/or casting an exterior lateral surface of the pole tube components and of the ring.

Method for manufacturing a pole tube for an electromagnet

A gas injector for directly injecting a gaseous fuel into a combustion chamber of an internal combustion engine, including a valve closure element for releasing and closing a passage opening, the valve closure element opening in the direction of a flow direction of the gas injector, a sealing seat between the valve closure element and a valve body, a flow-guiding element being situated downstream of the sealing seat in the flow direction of the gas injector and configured to form a gas jet to be injected into the combustion chamber.

Gas injector including an outwardly opening valve closure element

An injection valve for injecting fuel into a combustion chamber includes: a housing having at least one spray discharge orifice on a discharge side; a solenoid coil; a magnet armature linearly movable by the solenoid coil; a valve needle for opening and closing the spray discharge orifice, which valve needle projects through the magnet armature and is linearly movable along a longitudinal axis, the magnet armature being linearly movable in relation to the valve needle between a first stop and a second stop, the second stop being formed by a stop element having a stop face and a counter element having a counter face situated opposite the stop face, the stop element having an elastic design so that an angle between the longitudinal axis and the stop face is changed when the counter face strikes the stop face.

Injection valve

A fuel injection valve for injecting fuel includes: a coil, an internal pole, a valve sleeve, and a magnetic separating element, where the valve sleeve and the magnetic separating element are embodied in one piece as a powder injection-molded component, and the valve sleeve forms a magnetic region and the magnetic separating element forms a non-magnetic region, which are intermaterially joined to one another.

Fuel injector valve

A fuel injector for fuel-injection systems of internal combustion engines. The valve includes an electromagnetic actuating element having a solenoid coil, a fixed core, an outer magnetic-circuit component and a movable armature to actuate a valve-closure member which cooperates with a valve-seat surface provided on a valve-seat member. The valve is characterized by its extremely small outside dimensions. The entire axially movable valve needle, including armature and valve-closure member, has a mass of only m&#x3c;=0.8 g. The valve is suitable as a fuel injector, especially for use in fuel-injection systems of mixture-compressing internal combustion engines with externally supplied ignition.

Fuel injector

A fuel injection device includes at least one fuel injector, one mounting hole in a cylinder head for the fuel injector, and a decoupling element between a valve housing of the fuel injector and the wall of the mounting hole. As a lenticular spring element, the decoupling element has a nonlinear, progressive spring characteristic curve, such that a low rigidity of the decoupling element prevails during idle operation and a high rigidity of the decoupling element prevails during nominal system pressure.

Decoupling element for a fuel injection device

The fuel injection system has one high-pressure fuel pump and one fuel injection valve for each cylinder of the engine. The fuel injection valve has a first hollow injection valve member and a second valve member guided displaceably, inside the first valve member for controlling first and second opening(s), respectively into the associated engine cylinder. The second valve member is movable by the pressure prevailing in a pressure chamber in an opening direction counter to a closing force and is acted upon at least indirectly by the pressure prevailing in a fuel-filled control chamber, which pressure is controllable as a function of operating parameters of the engine such that the second injection valve member, by means of the pressure prevailing in the control chamber, can be blocked, independently of an opening motion of the first injection valve member in a position that closes the at least one second injection opening.

Fuel injection device for an internal combustion engine

The fuel injection system has one high-pressure fuel pump () with a pump work chamber () and one fuel injection valve (), communicating with the pump work chamber, for each cylinder of the engine. The fuel injection valve () has a first injection valve member (), by which at least a first injection opening () is controlled, and which is movable in an opening direction () counter to a closing force by the pressure generated in the pump work chamber (). Inside the hollow first injection valve member (), a second injection valve member () is guided displaceably, by which at least a second injection opening () is controlled, and which is movable by the pressure prevailing in the pressure chamber () in an opening direction () counter to a closing force; the second injection valve member () is acted upon at least indirectly by the pressure prevailing in a fuel-filled control chamber (), which pressure is generated, as a function of operating parameters of the engine, by a feed pump () such that the second injection valve member () either remains in its closed position, or can open.

A fuel injection valve with a valve body has a bore that contains a piston-shaped valve member. The valve member is guided in the bore with a sealing section and a guiding section; between the sealing section and the guiding section, the valve member is encompassed by a first pressure chamber and between the guiding section and the combustion chamber end, is encompassed by a second pressure chamber. In the guiding section of the valve member, an annular collar is provided and has a side oriented toward the combustion chamber and a side oriented away from the combustion chamber. The annular collar has a throttle connection embodied on it, which connects the sides of the annular collar to each other and thus produces a throttled connection from the first pressure chamber to the second pressure chamber.

Fuel injection valves for internal combustion engines

Growing community of inventors

Magstadt, Germany

Friedrich Moser