Carrier Corporation

Eugene L Mills, Jr

Rajendra K Shah

Lynn A Turner

Jerry Dean Ryan

Peter G Pierret

John M Palmer

Chris Puranen

James P Sodo

HVAC systems and methods are shown which use volumetric air flow and static pressure calculations that correct for different air densities encountered at different altitudes. With respect to the volumetric airflow rate, the systems and methods disclosed herein adjust the calculation of airflow rate to better match the BTU content of de-rated natural gas used at higher elevations, and therefore they are usable in HVAC systems that combust natural gas. The adjusted static pressure calculations may be used in any type of HVAC system.

Altitude adjustment for heating, ventilating and air conditioning systems

An air conditioning system that comprises a controller that is in electrical communication with a compressor, a condenser fan, a temperature sensor that measures the temperature of the ambient air, a temperature sensor that measures the temperature of a condenser coil of the air conditioning system, and a low pressure switch (LPS) that measure the pressure of a refrigerant disposed within the air conditioning system. An algorithm resident on the controller controls the controller to enter a low ambient cooling mode when the temperature of the ambient air is less than a set temperature. The algorithm further controls the controller so that a minimum and/or maximum cycling frequency is imposed on the condenser fan. The algorithm further controls the controller so that the controller does not respond to an LPS trip during the early part of a cooling cycle under low outdoor temperature conditions, which might not accurately indicate a system fault, but still shuts down the compressor in response to an LPS trip under conditions that truly indicate a system fault.

Air conditioning system for low ambient cooling

A motor starting apparatus () includes a motor starting relay () to switch a motor starting capacitor () into a motor circuit across a run capacitor (). The system control () includes an electronic voltage measurement circuit to measure a winding voltage () of the motor winding (). The system control () also includes a microprocessor to run an algorithm that causes the system control to switch the starting capacitor () out of the motor circuit when a measured winding voltage () exceeds a winding voltage threshold. A method to start a motor includes the steps of determining a motor winding voltage () threshold; closing the motor starting capacitor relay () when needed; closing a contactor () to supply power to the motor starting apparatus and the motor circuit; measuring a winding voltage (); comparing the measured winding voltage () to the voltage threshold; and opening the starting capacitor relay () when measured winding voltage () exceeds the voltage threshold indicating that the motor has been started.

Electronic method for starting a compressor

An electric heater is provided with an identifying resistor associated with a connection between the heater and a fan control. When the electric heater is connected to the control, the identifying resistor provides information with regard to the capacity of the particular electric heater that is being attached to the control. The control then utilizes this particular capacity to control both the electric heater and an associated fan motor.

Identification of electric heater capacity

Systems and methods of determining static air pressure in an HVAC system are provided. Static air pressure is mathematically determined as a function of system parameters, such as blower speed, blower diameter, system volume airflow rate, and/or blower motor torque. The determined static pressure can be used during HVAC installation and during HVAC monitoring and maintenance.

Method of determining static pressure in a ducted air delivery system using a variable speed blower motor

A heat pump having an indoor coil that operates as a condenser when the system is in a heating mode and an outdoor coil that operates as an evaporator when the system is in the heating mode. A variable speed indoor fan is used to move supply air over the indoor coil and a temperature sensor is arranged to provide ambient outdoor temperature data to a programmable computer. The computer contains a schedule for continuously adjusting the speed of the indoor fan in response to changes in the ambient temperature so as to maintain the temperature of the supply air at a constant level. In doing so, the compressor discharge pressure is also maintained within allowable limits and is held substantially constant.

Heat pump with improved performance in heating mode

An apparatus and method for a heat pump operating in the heating mode controls the condenser air flow rate and the condenser exiting air temperature depending in a first embodiment on the evaporator ambient temperature, and in a second embodiment, the evaporator air temperature and alternatively the condenser air flow rate or the condenser exiting air temperature, to alleviate a cold blow condition. The apparatus and method operate by sensing the evaporator ambient temperature with a sensor positioned proximate to the evaporator, and when that temperature is below a threshold value indicating a cold blow situation, determining by circuit means a modified condenser air flow rate to achieve at the same time a slower air flow and a higher air temperature, so that the cold blow condition is terminated or at least alleviated. The apparatus and method alternatively command the blower to achieve a determined condenser air flow, or to achieve a determined blower speed depending upon motor type, that results in a targeted condenser air flow or a targeted condenser exiting air temperature.

Apparatus and method of operating a heat pump to improve heating supply

An air conditioner or heat pump system is equipped with a thermostat control which includes a temperature sensor and a humidity sensor and an algorithm to control the low voltage signals to the indoor blower section and the compressor to control operation of each in response to the indoor temperature and humidity conditions and the desired temperature and humidity setpoints.

Humidity control thermostat and method for an air conditioning system

In an outdoor unit of a heat pump having a variable speed compressor, the fan speed is controlled in response to both the speed of the compressor and the temperature of the outdoor refrigerant such that the operating efficiency of the fan and its driving motor can be optimized over a full range of compressor operating speeds.

Growing community of inventors

Avon, IN, United States of America

Eugene L Mills, Jr