International Controls and Measurements Corporation

Icm Controls Corporation

Eric Christopher Wood

Andrew S Kadah

Weidong Pan

Hollis Jordan Gmyr

James H Ritchie

Michael P Muench

Benjamin Avery Freer

Hassan B Kadah

Kevin Jobsky

Michael James Cariseo

A thermostat or other in-line, two-conductor control device employs a power-stealing technique to obtain DC power for its electronic controls where the thermostat wire run has an R wire but no C (common) wire. The controlled switch for a reactive load, such as the gas valve relay or compressor contactor, is formed of a pair of power capacitors and a pair of switching transistors or other electronic controlled switches. The conductors for feeding DC power to control electronics are connected with the junctions of the power capacitors and their respective switching transistors. The power capacitors and switching transistors can be configured in respective series combinations, with the series combinations forming a parallel combination. The control device can be considered to have an energy storage and switching arrangement that forms with the load an L-C circuit and an electronic switch in circuit between the energy storage arrangement and the load and can be switched on and off to provide an input to a DC power supply.

Thermostat with power stealing

A touch-screen control panel interface has a dielectric flat or curved front panel and a printed circuit board with a front side and a reverse side which is the component side. Alphanumeric display module(s) or an LCD display and optional protective cap mounted on the reverse side of the circuit board are visible through window cutout(s) on the board. An array of LED indicators can be mounted on the back side of the circuit board and visible through cutouts in the board. Metallized capacitive pads on or adjacent the back side of the front panel at touch locations permit selection of various modes, functions, and settings. These pads may be formed on the flat front side of the circuit board, on the back of the front plate, or on an intermediate membrane. A microprocessor is connected with the various components and with capacitive pad. Icons may be printed onto the flat panel, in registry with the metallized capacitive electrode pads. A potting dam is formed of a back plate configured to adhere to the front panel and an open frame extending rearwards. Synthetic resin potting material fills the frame and hermetically seals the circuit board. Positions of the capacitive touch pads can be illuminated when active, as a guide for the user or operator. A second circuit board may be positioned in the frame directly proximal of the first circuit board, and optionally encapsulated.

Touch-sensitive flat-panel control and interface

A battery powered thermostat senses a battery voltage drop to a low-battery voltage level. At that point, the thermostat microprocessor provides a LOW BATTERY alert message, visible on the thermostat display. If the occupant fails to replace the power cells or does not notice the LOW BATTERY message, when the battery voltage drops further the microprocessor alters the thermostat set points. This reduces the number of heating or cooling cycles per day, and reduces the number of actuations of the latching relays in the thermostat, conserving remaining battery life. At a further drop in battery voltage the set points are changed additionally. Additional functions, such as second level heat, second level cooling, and fan speed, are disabled. The change in heat or cooling cycles induces the occupant to check the thermostat where he or she will notice the LOW BATTERY message.

DC thermostat with low battery response

A user interface of a controller has multiple touch-sensitive input transducers, e.g., capacitive pads. The pads are dynamically indicated: When any given touch sensitive input device is needed for input at a given step of the programming operation, an associated light source illuminates that input device so it is visible to the user. Those touch-panel input devices not needed for that are left unilluminated, and the microprocessor ignores any input from those input devices. At each step of the operation or programming of the controller, only those input transducers for the inputs that are permitted or relevant to that state are indicated. Correspondingly, only the inputs that are generated by actuating the input transducers for the valid (i.e., permitted or relevant) inputs results in a change in the state of the program in the microprocessor.

Controller with dynamically indicated input devices

Touch panel wall thermostat

Growing community of inventors

East Syracuse, NY, United States of America

Eric Christopher Wood