Lucent Technologies Inc.

Pd-ld, Inc.

At&t Bell Laboratories

American Telephone & Telegraph Co., At&t Bell Laboratories

Bell Telephone Laboratories

Fitel USA Corporation

Eliezer M Rabinovich

John Burnette MacChesney

David W Johnson, Jr

Vladimir Sinisa Ban

Boris Leonidovich Volodin

Elena D Melnik

Jerry Max Anderson

Aza E Mishkevich

Greg E Blonder

Allan James Bruce

Norman Roger Lampert

Edwin Arthur Chandross

Robert William Filas

Joseph Shmulovich

John Thomson, Jr

David Wilfred Johnson

Eva Milar Vogel

Henry Miles O'Bryan

Vincent J Fratello

David N Ridgway

Robert P Frankenthal

Ofer Sneh

The improvement of the performance of holographic glasses with recorded holograms as measured by a figure of merit of the holographic glasses is disclosed. The improvement in the figure of merit of the holographic glasses is obtained at least in part with the addition of arsenic in the formation of the holographic glasses. The presence of arsenic increases the figure of merit as measured at a wavelength of interest of a holographic glass with a recorded hologram as compared to a holographic glass with a recorded hologram that does not contain arsenic.

Methods for improving performance of holographic glasses

The specification describes processes for the manufacture of glass ferrules for optical fiber connectors wherein the glass ferrules have a composition comprising silicon oxide, alkali metal oxide, and aluminum oxide to which is added 1-35% of lead oxide.

Glass ferrule optical fiber connectors

Methods of making glass ferrule optical fiber connectors

The specification describes sputtering processes for the deposition of silicon dioxide films doped with high levels of oxides or other materials to alter the optical and/or electrical characteristics of the films. Sol gel methods are used to prepare composite sputtering targets of ultra fine mixtures of materials so the composition of the sputtered films replicate the composition of the target.

Deposition of highly doped silicon dioxide films

Cracking in thin sheets of sol-gel-produced material is avoided by use of a support liquid during gelation and drying. Silica glass, as well as other glass and ceramic bodies, is contemplated.

Fabrication including sol-gel float processing

The specification describes techniques for chemically machining extruded glass preforms used to draw glass ferrules for optical fiber connectors. Using the chemical machining technique the dimensions of the preform, including OD, ID, and the OD to ID ratio can be adjusted so that the dimensions of drawn ferrules meet strict dimensional standards. The technique is especially useful for adjusting the dimensions of extruded preforms that have an inherent bow along in the length of the preform. The technique allows adjustment in dimensions while preserving a desired OD to ID ratio. Also described are techniques for reducing eccentricity and/or ellipticity of hollow bore glass preforms.

Dimensional control in the manufacture of optical fiber ferrule

The inventive optical fiber connector comprises a glass ferrule that is strengthened by etching of the outer surface of the ferrule, followed by deposition thereon of a protective layer. Exemplarily, the ferrule is a vitreous silica ferrule drawn from a preform that was made by a sol-gel process. The ferrule is etched in buffered HF, and the protective layer is electroless deposited Ni, with a thin layer of Au thereon. Significant strength increases, exceeding 200%, are obtainable, with the strength being relatively unchanged after even a severe abrasion test.

Optical fiber connector comprising a glass ferrule, and method of making

The disclosed method of making a glass body by a sol/gel process comprises electrochemically assisted release of the gel body from the mold in which the body was formed. More specifically, the method involves gelation of a sol in a mold that comprises a first conductor member, with a second conductor member also being in contact with the sol and/or gel, and causing the flow of a current between the first and second conductor members, with the first member being the cathode. In consequence of the current flow a substantially liquid lubricating layer that facilitates removal of the gel body from the melt exists at the cathode/gel interface.

Method of making a sol-gel glass body and removing same from mold

Relatively large bodies of low-alkali silicate and other glass can be prepared conveniently by a particulate sol-gel process. The glass comprises at least 85 mole % SiO.sub.2, 1-12 mole % oxide of one or more of Li, Na, K, Rb, Cs, Ti and Zr, 0-6 mole % of oxide of Al, and optionally at most 2.5 mole % of oxide of elements other than Si, Li, Na, K, Rb, Cs, Ti, Zr and Al. The process comprises forming particles from a first sol that comprises Si and one or more of Li, Na, K, Rb, Cs, Ti and Zr, and optionally additionally comprises Al. The process further comprises forming a second sol by dispersing the particles in an aqueous liquid, gelling the second sol, and heat treating the resulting gel body such that the glass results.

Sol-gel method of making multicomponent glass

A sol-gel procedure is described for making display devices with luminescent films. The procedure typically involves hydrolysis and polymerization of an organometallic compound together with selected luminescent ions, and coating of a substrate and then heat treatment to form a polycrystalline layer. The procedure is particularly useful for making cathode ray tubes, expecially those for high power operation because of the excellent luminescence characteristics obtained, good thermal contact from the luminescent layer to faceplate and low cost of the procedure. Also described are the devices obtained which exhibit a layer of complex oxide with network structure much like the corresponding bulk compound.

Sol gel method for forming thin luminescent films

Incorporation of fluorine into a porous silica body, such as an unsintered body produced by a sol-gel method, by VAD or OVPO, reduces or eliminates bubble or pore formation upon re-heating of the glass formed by sintering of the porous material. Effective fluorine concentrations are between 0.01 and 5% by weight. The invention can be used advantageously in producing preforms and optical fiber.

Fabrication of high-silica glass article

High-silica glasses are formed by sintering a dried gel at temperatures below the liquidus. The gel may be formed by mixing colloidal silica particles or silica-containing liquids with appropriate liquids. Fragmentation of the gel during drying is advantageously avoided by redispersing the dried gel or sol in a liquid to yield a colloidal suspension which is then gelled, dried, and finally sintered below the liquidus.

Growing community of inventors

Berkeley Heights, NJ, United States of America

Eliezer M Rabinovich