Thermo Power Corporation

Gas Research Institute

Thermo Electron Corporation

Tecogen, Inc.

Edward F Doyle

Frederick E Becker

Kailash C Shukla

Maurice Nunes

Christopher I Metcalfe

Leo A Smolensky

Andrew Edward Masters

Francis A DiBella

Keith D Patch

Ann S Buck

Sotiris Kitrilakis

Robert DeSaro

A hybrid power assembly includes a thermophotovoltaic (TPV) power conversion module for converting radiant thermal energy into electrical power, and a battery in electrical communication with the TPV power source and rechargeable by electrical power generated by the TPV power source.

Hybrid power assembly

A burner/emitter/recuperator assembly for providing a high temperature radiant emitting surface, includes an elongated fuel pipe in communication with a fuel source and extending toward the combustion chamber, and adapted to flow fuel from the fuel source to a nozzle end of the fuel pipe proximate the combustion chamber, a primary air pipe disposed around the fuel pipe and in communication with a relatively cool primary air source, a nozzle end of the primary air pipe being substantially coincident with the nozzle end of the fuel pipe, and a recuperator for preheating secondary air disposed around a distal portion of the primary air pipe and in communication with a secondary air source and a swirler downstream of the recuperator. The relatively cool air from the primary air source and fuel from the fuel source flow through the primary air pipe and the fuel pipe, respectively, and mix with the hot air from the recuperator and swirler, exterior to the fuel nozzle and the primary air pipe nozzle end, to maintain a relatively cool fuel pipe nozzle end, and a relatively hot flame in the combustion chamber.

Burner and burner/emitter/recuperator assembly for direct energy conversion power sources

A combination flashlight and electrical power source assembly includes an emitter and fuel system module, a fuel cartridge module fixed to the emitter and fuel system module, a photovoltaic conversion module attachable to a selected one of the emitter and fuel system module and the fuel cartridge module, and a flashlight lens module attachable to the other of the emitter and fuel system module and the fuel cartridge module. When the photovoltaic conversion module is attached to the emitter and fuel system module and the flashlight lens module is attached to the fuel cartridge module, the photovoltaic conversion module is active, the flashlight lens module functions as an end cap, and the assembly functions as an electrical power source. When the flashlight lens module is attached to the emitter and fuel system module and the photovoltaic module is attached to the fuel cartridge module, the flashlight lens module is active, the photovoltaic conversion module functions as an end cap, and the assembly functions as a flashlight.

Combination flashlight an electrical power source assembly and emitter and reflector therefor

This invention relates to a heated steam atmosphere drying system comprising dryer in combination with an exhaust recompression system which is extremely energy efficient and eliminates dangers known to air dryers. The system uses superheated steam as the drying medium, which recirculated through the system where its heat of evaporation and heat of compression is recovered, thereby providing a constant source of heat to the drying chamber. The dryer has inlets whereby feedstock and superheated steam are fed therein. High heat transfer and drying rates are achieved by intimate contact of the superheated steam with the particles being dried The dryer comprises a vessel which enables the feedstock and steam to enter recirculate together. When the feedstock becomes dry it will exit the dryer with the steam and become separated from the steam through the use of a curvilinear louver separator (CLS). The CLS enables removal of fine and ultrafine particles from the dryer. Water vapor separated from the particles in the CLS as superheated steam, may then be recovered and recirculated as steam through the use of a compressor to either directly or indirectly heat the dryer, and a heat exchanger or a heater to directly provide heat to the dryer. This system not only provides a very efficient heat transfer system but results in a minimum carry-over of ultrafine particles thereby eliminating any explosive hazard.

Steam atmosphere drying exhaust steam recompression system

A system and method of controlling an electronically commutated motor (ECM) driving a blower to maintain the mass flow rate of the blower at a desired value. A microprocessor-based controller unit derives a motor control signal from just two inputs, namely the desired mass flow rate and a speed feedback signal representing the actual shaft speed of the ECM.

Mass flow rate control system and method

An improved method and apparatus for preheating cullet used as feedstock for a glass furnace. A direct contact raining bed is described through which cullet is fed by gravity flow, with furnace flue gases as combustion products of a separately-fired heater passed in counterflow to heat the cullet by direct contact. The preheater includes deflectors to retard passage and increase the path length of cullet flowing through the raining bed, and the deflector plates are mounted at specific declination angles and have their geometric parameters selected to optimize cullet residence time. Glass furnace systems are described which include the raining bed cullet preheater in series and parallel flow relationships with a glass batch preheater.

Direct contact raining bed counterflow cullet preheater and method for

A vapor engine including a cylinder in which a piston reciprocates and having an inlet valve in the cylinder head which is driven from its seat by the piston as it approaches the cylinder head. The time at which the valve is driven from its seat does not change relative to the top dead center position of the piston. The travel of the valve body is ballistic and the valve remains open for a time determined by a combination of the piston velocity at the initial contact, the distance the valve travels before hitting a stop from which it rebounds elastically toward its seat, the pressure drop across the valve and the mass of the valve. The exhaust valve of the engine may be either internal and actuated by mechanical forces or external, in which case it is actuated by pressure forces. In one embodiment of the invention the stop from which the valve rebounds may be adjustably positioned manually or automatically to control the period of time during which the intake valve is open.

Growing community of inventors

Dedham, MA, United States of America

Edward F Doyle