Isco, Inc.

Other

Douglas T Carson

Frederick Alan Nabity

Paul George Wright

Larry Lee Fritz

Raymond Hulinsky

John D Hull

Ralph E Setter

Lowell Robert Nickolaus

Louis F Lederer

Fredrick Alan Nabity

To insert an instrument into a flow stream of a sewer pipe from the street, the instrument is fastened to a holder, which in turn is fastened to a portion of an expansion ring opposite its two opened edges. A cord is fastened to one of the edges of the expansion ring and passes over a curved post mounted to the other edge of the expansion ring and extended upwardly in a direction parallel to the edges of the expansion ring so that it can be pulled to compress the expansion ring to a small diameter cylinder and released to expand it against the wall of a pipe. A post is mounted to the expansion ring to permit a long tool to grip the post and move the expansion ring into a sewer pipe where it is expanded and released.

Remote installation method and tool

To draw samples from a source of liquid, a pumping system measures the amount of liquid being pumped by detecting pump cycles and calculating the pumped liquid from this measurement and stored data including conduit size, pressure head and statistical data to correlate detected pump cycles with volume of liquid pumped. Pressure pulses cause by a peristaltic pump are sensed by a piezoelectric film positioned on an inlet conduit connecting the pump to the source of water and, when the liquid reaches a predetermined point determined by the nature of pulses are counted to determine the number of pump cycles.

Pumping system

To measure flow rates, the cross-sectional shape of the flow path is changed by inserting a multiple position gate into the flow path and altering the position of the gate to maintain the head of liquid constant with a reduced flow cross section. The position of the multiple position gate is correlated with the depth as measured with a bubbler to provide an indication of flow rate. To purge the bubbler line, a purge tank is located near the bubbler line. At timed periods or as manually initiated the controller causes an increase in pressure in accumulator portion of the purge tank. When a predetermined pressure is reached, a purge valve in the purge tank opens, rapidly allowing a burst of air at a substantial pressure and velocity to flow through the bubbler line to remove any material adhering to the bubbler outlet port. For this purpose, the purge tank acts as an accumulator until the pressure in the tank against the effective area of the inner portion of a purge valve element overcomes the resisting force of a spring, at which time the valve element moves slightly, permitting air to flow over a larger area of the valve element. This increases the area receiving the accumulator air pressure to include an outer portion of the valve element and this increased effective pressure area of the valve increases the force rapidly to cause the valve to snap open.

Purge system

To determine the average velocity of a fluid stream, an ultrasonic signal is transmitted into the fluid and reflected ultrasonic signal received. The signals are mixed with a frequency of the transmitted ultrasonic signals. A Fourier transform is performed on the signals, the largest coefficient used to normalize the signal and certain of the weighted signals are averaged.

Doppler shift velocity measuring system with correction factors

A method of making a sensor wherein flexible conduit means is assembled with a fixture having a strain-sensitive film and electrical connections are made to the film whereby variations in fluid pressure in the conduit means can be detected.

Method of making a sensor

To boost RPM and to minimize the back and forth transfer of kinetic energy between a crank and a connector/reciprocating member in mechanisms having a stroke that is four times the crankpin offset, a connector which attaches the reciprocating member to the crank is weighted with counterweights to produce an effective connector center of mass at a location on the connector that, while rotating around the crankpin defines a motion perpendicular to the oscillation of the reciprocating member such that the resulting translational inertia of the connector is equal to but perpendicular and ninety degrees out of phase with the translational inertia of the reciprocating member so that their combined kinetic energy is constant, thus resulting in a zero transfer in energy between the crank and the connector/reciprocating member through each revolution unless external force is applied to the crank or to the reciprocating member.

Low stress engine for converting motion between reciprocating and

Direct measurement ultrasonic velocity measuring system

Purging method

To draw samples from a source of liquid, a pumping system measures the amount of liquid being pumped by detecting pump cycles and calculating the pumped liquid from this measurement and stored data including conduit size, pressure head and statistical data to correlate detected pump cycles with volume of liquid pumped. Pressure pulses caused by a peristaltic pump are sensed by a piezoelectric film positioned on an inlet conduit connecting the pump to the source of water and, when the liquid reaches a predetermined point determined by the nature of the pulses, the pulses are counted to determine the number of pump cycles.

Ultrasonic fluid velocity measuring system

To measure flow rates, the cross-sectional shape of the flow path is changed by inserting a multiple position gate into the flow path and altering the position of the gate to maintain the head of liquid constant with a reduced flow cross section. To maintain the head at a desirable range, the depth is measured and controls the position of the gate as a feedback signal. The position of the multiple position gate is correlated with the depth to provide an indication of flow rate. For this purpose, a flow path housing is clamped to a pipe and a multiple position gate is moved by pneumatic pressure into the flow stream to change the flow cross section. The depth of the head upstream of the gate is measured and the position of the gate is measured. Flow rate is determined from these two measurements. Sampling may be performed at an increased depth caused by the gate.

Variable gate flow analyzing method and apparatus

To reduce space requirements, vibrations and certain stresses in a motion converting mechanism, a rod is constrained to reciprocate within a housing where the rod is attached to the crankshaft by a cylindrical shaped connector that orbits around the crankpin in a direction opposite that of the crankshaft while rotating inside the rod. Through the center portion of each stroke, the connector also interfaces directly with the housing by such means as a cam cam-follower or gearing to eliminate a second degree of freedom at midstroke. The resulting motion defined for the center of the connector and the rod is sinusoidal being twice that of the motion of the crankpin in the axis of reciprocation. The resulting stroke is four times the crankpin offset.

Motion converting mechanism

To reduce space requirements, vibrations and certain stresses in an engine, a different one of two pistons is mounted on each end of a single piston rod to which the crankshaft is attached by a cylindrical shaped connector that orbits around the crankpin while rotating inside the piston rod. The crank interfaces directly with the piston rod through gear portions or a cam-cam follower through the center of each stroke. To reduce vibrations and certain stresses in an engine, a different one of two pistons is mounted on each end of a single piston rod to which the crankshaft is attached by two arms extending orthogonally from its central portion, each arm being mounted to a different one of two different connecting rods. To balance inertia forces, two oppositely rotating crankshafts are counter-weighted to balance the inertia forces of the assembly in its axis of oscillation and to balance each other outside that axis of motion, or two piston assemblies oscillate opposingly in the same axis eliminating the need for the crankshafts to balance their inertia forces.

Growing community of inventors

Lincoln, NE, United States of America

Douglas T Carson