New York Air Brake Corporation

Derick Call

Howard E Huber, Jr

Steven R Newton

Jeffrey F Sauter

Lawrence E Vaughn

Brian Graves

James Lewis Vendlinski

Eric C Wright

Bryan M McLaughlin

Jason Connell

Keith Parnapy

Christopher J Ferguson

Danial Rowland

Steven Michael Barnhart

Carl Banks

Joshua D Woodruff

Nicholas Van Derzee

John M Reynolds

Scott Margeson

Justin Sven LaCosse

Craig Floyd Hughes

Laurence E Vaughn

James Brierley

Justin Lacosse

Howard E Huber

A combined dirt collector and cutout cock (CDC & COC) device for a rail car control to prevent unintentional re-pressurization of the control valve and rail car braking system. The device has an inlet configured for interconnection to an air supply, an outlet configured for interconnection to a control valve of a rail car, a valve moveable between a first position where an inlet is connected to an outlet and a second position where the inlet is isolated from the outlet, and a control valve vent positioned downstream of the valve and configured to open in response to the valve being moved into the second position. The valve may include a ball having a first passageway for selectively connecting and disconnecting the inlet from the outlet and a second passageway formed therethrough that is positioned to interconnect the outlet with the vent when the valve is in the second position.

Combined dirt collector and cutout cock having controlled venting

A brake cylinder maintaining system that combines a brake cylinder maintaining check valve and a quick service limiting valve into a single unit to have lower hysteresis, and thus more precise BCM regulation pressure and a smaller pressure offset. The check valve and quick service valve are coupled to provide a single system having multiple valve seats for selective communication between quick service pressure and brake cylinder pressure on one hand, and between a brake cylinder maintaining pressure and brake cylinder pressure on the other hand.

Brake cylinder maintaining with improved pressure regulation

A system for monitoring usage of rail car brake equipment and determining whether the actual lifespan of the brake equipment is shorter than an expected lifespan had the brake equipment been used under normal or constant parameters. The system includes a sensor for collecting and outputting data indicating how the brake equipment has been actually used. A controller is programmed to receive the data regarding how the brake system component has been used and to calculate whether the brake system component has an estimated lifespan that is shorter than the expected lifespan. The sensor may comprise an ambient temperature sensor, a flow sensor that determines the air used by the braking system that includes the brake system component, and/or a pressure sensor that can determines how frequently and in what manner the brake system has been used.

Brake equipment wear monitoring for remaining useful life

An electronically controlled pneumatic (ECP) overlay control valve can selective switch between a conventional pneumatic mode and an ECP mode. In ECP mode, the overlay control valve shunts the brake cylinder pressure of the pneumatic control valve which allows a relay valve to build or exhaust pressure in the brake cylinder in response to an electronically controlled apply/release circuit. In conventional pneumatic mode, the overlay control valve disconnects the relay valve and allows a conventional pneumatic control valve to control the pressurization and exhausting of the brake cylinder.

Electronically controlled pneumatic (ECP) overlay control valve

A bypass for an air dryer having an inlet, a prefiltration stage having a drain valve to purge contaminants, a pair of inlet valves in communication with the prefiltration stage to control the flow of compressed air through the desiccant towers, and an outlet coupled to the pair of desiccant towers. The bypass may be a bypass valve that is normally open to the outlet when the air dryer is unpowered and pilotable to be a closed to allow air to flow to the prefiltration stage when the air dryer is powered. The bypass may be a three-way valve that is normally coupled to the outlet and that may be piloted to connect to the prefiltration stage when the dryer is powered. The bypass may also be a check valve that opens in response to pressure in the inlet to allow compressed air to flow directly to the outlet.

Air dryer with prefiltration stage bypass

A railway vehicle parking brake that can provide the appropriate tension to the braking system using a motor, a brake chain drum interconnected to the motor to take up or release a brake chain, a load arm deflects in response to tension in the brake chain, and a switch that is closed by the load arm when it deflects. A movable sheave interconnects the brake chain and the load arm and is positioned between the brake chain drum and a fixed sheave over which the brake chain is looped. A control method considers the position of the first switch to determine whether to the motor off when applying the brakes and the amount of current being drawn by the motor to determine whether to the motor off because of a system failure.

Locomotive parking brake

A control valve for an automatic parking brake having an inlet for coupling to a source a brake pipe pressure, an outlet for coupling to a control inlet of the automatic parking brake and a pilot for coupling to the source of brake pipe pressure. The control valve is moveable between a first position where the inlet is in communication with the outlet and a second position where the inlet and the outlet are isolated from each other in response to a predetermined amount of brake pipe pressure at the pilot. The control valve includes a spring biasing the control valve into the first position.

Control system for automatic parking brake of rail vehicle

A locking mechanism for a brake cylinder that has a tube surrounding the hollow shaft of the brake cylinder with a first set of teeth formed along an outer surface thereof. A gate having a second set of teeth corresponding to the first set of teeth is moveable in between a first position, wherein the first and second set of teeth are engaged to prevent movement of the brake cylinder piston, and a second position where the first and second set of teeth are disengaged to allow movement of the brake cylinder piston. A spring biases the gate into the locked position and a supplemental piston responsive to a source of brake pipe pressure can move the gate into the unlocked position so that the main piston is free to move.

Automatic parking brake for body mounted brake cylinder

A slack adjuster for narrow gauge rail cars including a housing having a body with a first clevis joint, a coupling secured to the body, and a guide tube secured to the body coupling. A lever is pivotally coupled to the housing for moving an actuator coupled to a clutch. The clutch is engaged with the external threads of a rod and moveable between a first captured position, a second position where the clutch is free to rotate, and a second captured position to selectively control movement of the rod. Movement of the lever withdraws the actuator so that the clutch releases and can spin, allowing the threaded rod to translate from the retracted to extended positions. Opposing forces applied to a ram causes the clutch to move to the second captured position, thereby preventing rotation of the clutch and preventing the threaded rod from retracting further into the housing.

Slack adjuster for narrow gauge railroad cars

A brake cylinder maintaining valve may include spool valves or poppet valves. When the pressure in the brake cylinder drops below its original set pressure, such a maintaining valve may feed brake pipe (BP) pressure through a choke to replenish and maintain brake cylinder (BC) pressure up to a certain point. If the leak is too great, such as when it exceeds the capacity of the choke, the brake cylinder pressure will not be maintained. Such a maintaining valve may be either integrated into the control valve, or it may be mounted remotely to the brake system. If mounted remotely, it may be connected by multiple ways, including through a conventional 4-port access plate.

Growing community of inventors

Evans Mills, NY, United States of America

Derick Call