Motorola Corporation

Continental Automotive Systems Corporation

Temic Automotive of North America, Inc.

Teletype Corporation

Zenith Electronics Corporation

Elb Electronics, Inc.

Motoral, Inc.

Dennis L Stephens

Patrick A O'Gorman

John G Konopka

Jeffrey D Merwin

Donald J Remboski

Anand K Upadhyay

Guang Rong Liu

Edward E Li

John M Wong

Scott W Repplinger

Philip D Gunderson

Edmund C Feldy

Xiaoxiang Cheng

Hubie Notohamiprodjo

Kenneth D Labudda

Randy Russell

Young G Kang

Brian D Conway

Wayne F Salata

Patrick A O′Gorman

Steven J Purdy

Circuitryfor a solid-state lighting arrangementdesigned for as a replacement for a gas discharge lamp used in a lighting fixture having a ballast. The circuitryunsafe flow of current through the solid-state lighting arrangement, under non-operational conditions and during installation of the lighting arrangement, so as to provide compatibility with safety standards for use with discharge lamps.

LED fluorescent lamp emulator circuitry

The resonant frequency of a reactive circuit is determined in situ by determining phase angle differences between an A.C. driving voltage applied to a transformer primary winding and an induced alternating current in the transformer secondary winding. The phase angle is determined indirectly by detecting when the driving voltage applied to the primary changes its polarity and when an induced current in the secondary changes its polarity. The time difference between those polarity changes indicates whether the voltage leads or lags the current or is in phase. A driving voltage frequency is adjusted in real time until the phase angle differences disappear. A duty cycle of the driving signal applied to the primary is also adjusted to change the voltage induced in the secondary winding. The duty cycle is adjusted by changing either a phase of primary driving voltages or the duty cycle of primary driving voltages.

Apparatus and method for determining a resonant frequency of an LC circuit in situ, by comparing voltage and current polarity changes

An output voltage of an LLC resonant converter circuit is received. The received output voltage is analyzed to determine whether the received output voltage is within an acceptable operational range. When the output voltage is not within the acceptable operational range and the operational frequency is below a maximum predetermined frequency, the operational frequency of the LLC resonant converter circuit is adjusted. The adjustment of the operational frequency is effective to change the output voltage to a value that is within the acceptable operational range. When the output voltage is not within the acceptable operational range and the operational frequency is above the maximum predetermined frequency, a phase shift in the LLC resonant converter circuit is adjusted. This adjustment is effective to change the output voltage to a value that is within the acceptable operational range.

Efficient LLC resonant converter having variable frequency control and fixed frequency phase-shift PWM

Methods and systems for power conversion are disclosed, including receiving at least one interrupt indicative of a transient power condition of the power converter and switching the processor to operate in a second mode from a first mode responsive to the interrupt. The switching enables the processor to allocate greater resources to process a power output parameter of the power converter operating in the transient power condition compared to resources allocated by the processor operating in the first mode to process the power output parameter.

Digitally controlling a power converter

Disclosed herein is an electrical system topology for voltage regulation in a 12-volt vehicle power distribution system. Particularly, a single transistor power converter is configured to operate in both as a traditional voltage regulator mode (i.e., as buck converter to reduce the field voltage applied to an alternator to a value less than that available from the main bus) and as an alternator field current boost converter (i.e., as a boost converter to boost the field voltage applied to an alternator to a value greater than that available from the main bus). The converter may also include a controller that incorporates a thermal model of the alternator to limit the amount of voltage boost applied and/or direct temperature measurement of the alternator or alternator components. Additionally, these two approaches may be combined such that measured temperatures are used to refine the temperature estimated by the thermal estimator.

Single transistor alternator field buck/boost

Disclosed herein are a variety of different electrical system topologies intended to mitigate the impact of large intermittent loads on a 12 volt vehicle power distribution system. In some embodiments the intermittent load is disconnected from the remainder of the system and the voltage supplied to this load is allowed to fluctuate. In other embodiments, the voltage to critical loads is regulated independently of the voltage supplied to the remainder of the system. The different topologies described can be grouped into three categories, each corresponding to a different solution technique. One approach is to regulate the voltage to the critical loads. A second approach is to isolate the intermittent load that causes the drop in system voltage. The third approach is to use a different type of alternator that has a faster response than the conventional Lundell wound field machine.

Automotive electrical system configuration

The linear position of a moving mechanical component is determined. A plurality of values of a quantity using a plurality of sensors is sensed and the sensed values are indicative of the linear position of the mechanical component. The plurality of sensed values are converted into a plurality of best linear position estimates concerning the mechanical component. One or more compensations are applied to at least some of the plurality of best linear position estimates. Each of the compensations are applied to account for a relative positioning of one of the plurality of sensors with respect to the others. A plurality of weighting factors associated with each of the plurality of best linear position estimates are determined. The position of the mechanical component is determined using the plurality of best linear position estimates and the plurality of weighting factors.

Position sensing system and method

Methods and systems for minimizing power loss in generator are disclosed, including providing one or more operating parameters for a generator, and determining an optimal field power and an optimal phase angle, where the optimal field power and the optimal phase angle substantially minimize a power loss in operating the generator at the one or more operating parameters.

Systems and methods for optimizing the operation of a generator

Automotive electrical system

Disclosed herein is an automotive electrical system including a FET based rectifier and method of controlling the FET based rectifier without using either an alternator shaft position sensor or current sensors on each phase of the alternator output to control the switching of the FETs. In accordance with the teachings herein, the voltage and current on the DC bus of the automotive electrical system are sensed and switching of the FETs is controlled by a microcontroller that determines the appropriate switching times based on these sensed parameters.

Active rectification of alternator output without using a position sensor

An apparatus and method for driving a halogen lamp. A driving circuit is provided that is operable near a series resonance frequency. The driving circuit is coupled to the lamp in a series configuration. During startup, the circuit is driven above resonance. After the lamp has warmed up, the circuit is driven substantially at resonance. A controller is coupled to the driving circuit. The controller is operable to control the frequency of operation of the driving circuit.

Resonant circuit for halogen lighting

Disclosed herein are two techniques, neutral point switching and field voltage boost, that will increase the output of today's 12 volt automotive electrical systems in vehicle idle conditions solely by the addition of circuitry. Neutral point switching enables the flow of a third harmonic current, which does not normally flow at low speeds, but only at high speed. Boosting the field voltages can be obtained by integrating a field voltage boost circuit and voltage regulator to increase the field voltage, and consequently the field current, above the level obtained from the battery. Furthermore, the transient response of the alternator to a change in load is improved by temporarily increasing the field voltage above the level needed to sustain the load. These two techniques are compatible, and thus may be implemented together, or may be implemented independently. No changes to a standard alternator are required to accommodate the proposed additional circuitry.

Growing community of inventors

Niles, IL, United States of America

Dennis L Stephens