Graco Minnesota Inc.

Graco Inc.

Dennis J Van Keulen

David L Fehr

John Russell Ingebrand

Vannareth J Chum

Vu K Nguyen

Jeremy P Jurmu

Lawrence P Jeutter

David D Loukusa

Jeremy Peter Jurmu

Christopher J Van Keulen

A mix manifold () includes a plurality of valves to control the flow of material therethrough. First and second valves () are linked for simultaneous actuation. The first and second valves each include valve members () disposed within and rotatable relative to seal bodies (). The valve members seal against the seal bodies and the seal bodies seal against the manifold. A solvent valve () also includes a valve member () in a seal body (). The first and second valves are configured to open only when the solvent valve is closed. The solvent valve is configured to open only when the first and second valves are closed. The solvent valve can rotate between a plurality of positions to control the flow of solvent to flowpaths downstream of the first and second valves.

Mix manifold and valve seal assembly

A method for a system having a plurality of primary fluid sources and a fluid output with a common pump includes halting pumping of a first fluid, isolating the common pump from the fluid output and the primary fluid sources, connecting an inlet of the common pump to a solvent source and a compressed air source, and an outlet of the common pump to a waste fluid dump, filling the common pump with a first purge volume of solvent, cycling the common pump in a flush mode, operating the common pump in a timed flow mode, and connecting an inlet of the common pump to a second primary fluid source, and an outlet of the common pump to the output line, and starting pumping of a second fluid from the second primary fluid source through the output line.

Spray system pump wash sequence

A control method for a two-component spray system having first and second pumps for separate fluid components includes registering a target spray pressure, registering a material-specific pressure factor margin, sensing an output pressure of the second pump, and identifying a failure condition in the event that the sensed output pressure remains further than the pressure factor margin from the target spray pressure for at least a threshold time.

Spray system pressure differential monitoring

A two-component pumping system includes a first pump for pumping a first component, a second pump for pumping a second component, a motor, and a yoke assembly for connecting the motor to the first pump and the second pump and driving them simultaneously. The first pump includes a first displacement rod that reciprocates in a first pump axis. The second pump includes a second displacement rod that reciprocates in a second pump axis parallel to the first pump axis. The motor includes a drive shaft configured to reciprocate in a drive axis that is parallel to and in a common plane with the first and second pump axes. The motor is also configured to drive the first and second displacement rods in unison. The yoke assembly includes a top connector and a shoe. The top connector connects to the drive shaft.

Plural component proportioner comprising a first pump and a second pump simultaneously driven by a motor connected to the pumps by a yoke assembly comprising a shoe, a tie plate including a slot, and a tie rod

A spray system has a pump with a double-action reciprocating plunger balanced to receive equal up-stroke and down-stroke assist from a pre-pressurized supply. The reciprocating plunger has identical working surface area on opposite first and second axial faces. A pumping system has a double-action reciprocating plunger with upward- and downward-facing spacers. The plunger travels axially within a proportioning cylinder with first inlet and outlet ports at a first axial end, and second inlet and outlet ports at an opposite second axial end. When the plunger is at its top-most position, the upward-facing plunger occludes the first inlet and outlet ports without blocking flow. When the plunger is at its bottom-most position, the downward-facing plunger occludes the second inlet and outlet ports without blocking flow.

Proportioning cylinder for spray system

A spray system includes a fluid source, a sprayer, a pump cylinder, a plunger, a pump motor, first and second inlet and outlet valves, a plurality of valve seals, a seal lubricant reservoir, and gravity fed seal lubricant lines. The pump cylinder is disposed fluidly between the fluid source and the sprayer. The plunger is situated within the pump cylinder and positioned by a displacement rod. The pump motor is configured to drive the displacement rod so as to reciprocate the plunger within the pump cylinder. The valve seals are disposed about the each of the first and second inlet and outlet valves. The lubricant seal lines carry seal lubricant from the reservoir to each of the valve seals.

Multi-point seal lubrication system

A method for a system having a plurality of primary fluid sources and a fluid output with a common pump includes halting pumping of a first fluid, isolating the common pump from the fluid output and the primary fluid sources, connecting an inlet of the common pump to a solvent source and an outlet of the common pump to a waste fluid dump, actuating the common pump first in a pumping mode, then in a recirculation mode, and then in a flush mode, connecting an inlet of the common pump to a second primary fluid source, and an outlet of the common pump to the output line, and starting pumping mode pumping of a second fluid from the second primary fluid source through the output line.

Plural component proportioner

A gun flush box is controlled by a plural component proportioning unit. When a color change is desired, the operator places the spray gun in the flush box. When a new color is selected, the control system automatically triggers the gun and flushes the gun with solvent with the flush material safely routed to a waste container. The control system automatically triggers the gun to refill the lines with new color paint without using excess paint as it displaces the flush solvent. This system is also capable of working with two guns in operation.

Growing community of inventors

Rogers, MN, United States of America

Dennis J Van Keulen