Zhejiang University

Delta Electronics (shanghai) Co., Ltd

Fuji Electric Systems Co. Ltd.

Fuji Electric Co., Ltd.

Dehong Xu

Kazuaki Mino

Jinfa Zhang

Kai Dong

Yi Chen

Yasuhiro Okuma

Wenxing Zhong

Yanjun Zhang

Hao Li

Xiaofeng Wu

Xiao-feng Wu

Zhiwei Wen

Disclosed in the present application is an incompletely compensated wireless power transfer system. On the basis of an SS compensated wireless power transfer system topology, a primary side capacitor Cand a secondary side capacitor Ctake specific values, and in combination with a phase shift frequency modulation control method, a coupling range of a system output rated power is improved. According to the present application, by finding an appropriate combination of the primary side capacitor Cand the secondary side capacitor C, the system can output a required rated power in a larger coupling range under the condition of incomplete compensation.

Incompletely compensated wireless power transfer system

A control method for a power factor correction circuit is disclosed. The power factor correction circuit includes a first bridge arm, a second bridge arm, an output capacitor and an active clamp unit. The control method includes steps of providing a first driving waveform to control a main switch, providing a second driving waveform to control an auxiliary switch, and providing a third driving signal to control a fifth switch. A first delay time is between the turning-off time point of the third driving signal and the turning-on time point of the first driving waveform, a second delay time is between the turning-on time point of the first driving waveform and the turning-off time point of the second driving waveform, and a third delay time is between the turning-off time point of the second driving waveform and the turning-on time point of the third driving signal.

Control method for power factor correction circuit

Disclose is a wireless electric energy transmission system for realizing PFC through secondary side modulation. According to the system, on the basis of a traditional wireless charging system topology, a traditional PFC circuit is removed, a grid voltage is turned into a 100 Hz voltage through uncontrolled rectification to directly supply power to an inverter of a primary side of a wireless charging system; an active full-bridge rectifying structure is adopted at a secondary side, and the PFC function is achieved only through secondary side modulation, wherein under the situation that a phase shift angle &#x3b1; of the inverter of the primary side is given.

Wireless electric energy transmission system for realizing PFC through secondary side modulation

A power factor correction circuit includes an input power source, a first bridge arm, a second bridge arm, an output capacitor and an active clamp unit. The first bridge arm includes a first switch and a second switch in series. The second bridge arm includes a third switch and a fourth switch in series. The active clamp unit includes a second inductor, a clamp capacitor and a fifth switch. The power factor correction circuit may realize the ZVS function of the first switch and the second switch by the collaboration of the active clamp unit and the conduction/non-conducting state of the first switch, the second switch, the third switch and the fourth switch.

Power factor correction circuit

An entirely integrated EMI filter is based on a flexible multi-layer strip material. An EE or EI core comprises two side pillars and one middle pillar and forms a closed magnetic circuit. The middle pillar has an air gap. A first winding and a second winding respectively are wound around the two side pillars in a same winding direction. The middle pillar is wound with a third winding and a fourth winding, or with only a fifth winding. Passive components (e.g., all passive components) of the EMI filter are integrated into one core so that in its differential mode, insertion loss is significantly reduced, the size and volume are reduced, and the distribution constant of the EMI filter has less impact on the filter's performance.

Entirely integrated EMI filter based on a flexible multi-layer strip material

An integrated structure of common-mode inductors and differential-mode capacitors in an EMI filter realized using a flexible circuit board, including: a closed magnetic circuit formed by a first magnetic core and a second magnetic core, optionally including an air gap formed in a middle pillar of the magnetic cores, and with a flexible printed circuit board (FPC) wound on at least one pillar, the FPC formed by laminating alternating insulating and copper foil layers. The integrated structure of inductors and capacitors is advantageous in reducing the volume of the EMI filter and improving the power density of an electronic power transformer.

EMI filter with an integrated structure of common-mode inductors and differential-mode capacitors realized by flexible printed circuit board

An integrated structure of passive elements in an LLC resonance converter realized by flexible circuit boards includes a closed magnetic circuit formed by first and second magnetic cores, a tubular, double-sided, flexible circuit board, tubular magnetic-material layer and tubular, single-sided, flexible circuit board. The single-sided circuit board is coaxially sleeved in turn from inside outwards on a magnetic core column of the closed magnetic circuit. The tubular, double-sided, circuit board is a laminated plate material formed in turn of a first insulating layer, first copper foil, insulating medium layer, second copper foil and second insulating layer. The tubular, single-sided, circuit board is a laminated plate material formed in turn of a third insulating layer, third copper foil and fourth insulating layer. The integration of a resonance capacitor, resonance inductor, shunt inductor and transformer in a LLC resonance converter is realized by using these flexible circuit boards.

Growing community of inventors

Hangzhou, China

Dehong Xu