Light and Motion Industries, Inc.

David William Tolan

Daniel T Emerson

Brooks Patrick Lame

Jarod Armer

Joseph G Goldman

Benjamin McGeever

David P Heiss

Kevin Govan

Eric Simon

Alejandro Cota

Devin P McKee

Brooks Pattrick Lame

Geoffrey Barker

An LED drone light of high power and very light weight has an LED circuit board cooled by a foamed metal matrix of copper or aluminum. Preferably bonded to a disc or puck which is thermally bonded to the back of the PCB, the foamed metal matrix can be cooled by a small fan attached to the light's housing.

Lightweight powerful LED light for drones

A camera and LED strobe unit are operated such that the strobe unit produces a series of bursts, such as approximately ten per second. The bursts are used either to illuminate a subject at a series of different light levels, to then present a series of images to the user to select the best exposure, or to produce a series of images of a moving subject within a single frame. The light unit has a continuous mode of LED light output, but can be switched to the burst mode for high power bursts in rapid succession.

Exposure optimization for digital burst light

A control system for underwater diving lights utilizes sounds of specific frequency emitted by action of a diver to control one or more remotely positioned diving lights.

Simple sound control of underwater lights

An LED light is operated in both continuous steady output and, as desired, a periodic high power burst of light that drives the LED beyond its rated output for short periods. A single cost effective circuit to perform both types of control delivers highly regulated output under both high power burst mode and continuous mode while maintaining maximum feedback resolution in the primary (continuous) output mode. Active elements are used to switch the signals from conventional current sensing elements through a controlled scaling network before joining the rest of the regulating circuit. This results in ability to produce a high efficiency, well-regulated, fast rise and fall, rectangular average peak value waveform, electric current pulse to power a single or combination of LEDs to a high output level, effecting a transition between a constant lighting level and a higher output, pulsed duration lighting level for photographic and motion image capture.

Combination high power LED strobe and continuous light

A bicycle light has in one embodiment a mounting base to connect to the bicycle, and an LED light unit for insertion into and removal from the base. The light unit includes a printed circuit board with LED driver and a rechargeable battery, all of which are encapsulated by a direct overmolding that forms a casing for the unit. For charging the light unit is pulled out from the base and plugged into a USB port via an extending USB blade. A motion detector on the PCB shuts off the LED if no motion is detected for several minutes, thus eliminating need for any exterior switch. Another embodiment is without the USB blade, with the battery charged by inductive charging.

Compact, waterproof rechargeable light assembly

An LED array and driver design minimizes space requirements and simplifies assembly, while reducing costs. A printed circuit board with LED driver electronics has a central opening through which the LED array is mounted. In one form the LED array is a chip on board (COB) array, the array being circular and fitting closely within the central opening of the PCB. Four integral leaf springs are formed into the flat PCB, in position to push the LED array down when the PCB and LED array are attached against the heat sink. Two of the springs have electrical contacts that make contact with those of the LED array. With the LED array and driver circuit on the face of a light assembly, the space rear of the driver circuit is free to be open to air flow for cooling.

Coplaner LED array and driver assembly

A bicycle tail light or front light has a mounting base to connect to the bicycle, and an LED light unit for insertion into and removal from the base. The light unit includes a printed circuit board with LED driver and a rechargeable battery, all of which are encapsulated by a direct overmolding that forms a casing for the unit. For charging the light unit is pulled out from the base and plugged into a USB port. A tongue with USB blade at the back of the light unit functions to secure the light unit to the mounting base, and the attachment of the units switches power to the light unit. A motion detector on the PCB shuts off the LED if no motion is detected for several minutes, thus eliminating need for any exterior switch.

Growing community of inventors

Carmel, CA, United States of America

David William Tolan