Westinghouse Electric Corporation

Other

Eaton Corporation

Eaton Intelligent Power Limited

Electric Power Research Institute Incorporated

David Robert Smith

Shan C Sun

John F Rossi

Larry L Church

Thomas J Kenny

Charles A Peterson

Joseph R Rostron

Clive W Kimblin

John Robert Moffat, Jr

Albert H Maxwell, Jr

Michael H Silverberg

William H South

Randall N Avery

Michael W Thomas

Jack F Trezza

Thomas D Poyser

Garrett S Sylvester

David W McElroy

John D Borst

Marc Andre Faulkner

John W Bankoske

A device is presented for use in power distribution networks, for limiting transient overvoltages during backfeed on a network primary feeder whose feeder breaker is open and whose network protector fails to open. The device is self-contained and self-protecting, and limits the transient voltages due to an arcing single line-to-ground fault by inserting a resistance into the zero-sequence network of the primary feeder. Limiting transient overvoltages reduces damage to and prevents failures of various network components, and in particular, prevents multiple insulation failures during backfeed and reduces failures during backfeed in microprocessor network protector relays on the secondary side of network transformers whose protectors are open. In addition, the device reduces transient overvoltages associated with re-energizing a network primary feeder by closing the station breaker when all network protectors on the feeder are open, as occurs when restoring a network primary feeder that has been out of service.

Network primary feeder self protected transient limiting device

In one embodiment, a network protector for a spot network includes a circuit breaker and a network protector relay coupled to the circuit breaker. The network protector relay is structured and configured to have network protector relay non-sensitive trip settings for controlling operation of the circuit breaker that will cause the network protector to remain closed when: (i) an angular difference (&#xb1;) between a transformer phase-to-neutral voltage of the first feeder branch and a transformer phase-to-neutral voltage of the second feeder branch is less than or equal to a first threshold value, and (ii) a magnitude difference (&#xb1;) between the transformer phase-to-neutral voltage of the feeder branch and the transformer phase-to-neutral voltage of the second feeder branch is less than or equal to a second threshold value.

Network protector control for spot network fed from feeder sources having voltage differences

A network protector relay controls a circuit breaker connected between polyphase feeder and network busses. A circuit samples polyphase circuit breaker current and network voltage to generate digital polyphase current and voltage samples. A microcontroller generates positive sequence current and voltage vectors from the current and voltage samples. A first trip algorithm trips the breaker in response to the positive sequence current vector being in a first trip region of a first trip characteristic with respect to the positive sequence voltage vector. The first trip characteristic is defined by a reverse trip setpoint and a first positive angle. A second trip algorithm trips the breaker in response to the positive sequence current vector being in a second trip region of a second trip characteristic with respect to the positive sequence voltage vector. The second trip characteristic is defined by the reverse trip setpoint and a second negative angle.

Network protector relay and method of controlling a circuit breaker employing two trip characteristics

There is provided a system and method for locating faults in power distribution systems with complex topology, such as multi-phase urban networks (6), utilizing reliable time-delay techniques as well as a transponder (22) at a monitoring point to sense the arrival of the transient fault pulse and for transmitting a timing pulse a known time delay after sensing the arrival of the transient fault pulse and a calibration pulse a known time delay after transmitting the timing pulse. Installed along the power distribution system at key locations are receiver stations (4, 4a, 4b) capable of sensing the arrival of the transient fault pulse, timing pulse and calibration pulse and measuring the time intervals occurring between each. The location of the fault is then determined based on these timing intervals, known time delays and the known propagation velocity of the electric power cables in the power distribution system. Fault location accuracy is further enhanced by factoring rise-time effects of the sensed pulses into the time interval measurements.

System and method for locating faults in electric power cables

A microprocessor-based transformer monitoring system to provide continuous on-line monitoring and analysis of transformer operation. The transformer monitoring system periodically monitors various parameters related to transformer load and condition. Maximum, minimum, and instantaneous values of the parameters are stored and analzyed. To perform the analysis, a hierarchy of thresholds is associated with each parameter. When a parameter exceeds any one of the thresholds, a response is produced by the transformer monitoring system. The type of response depends on the level of the exceeded threshold in the hierarchy. The range of response produced by the transformer monitoring system includes: continuing normal periodic data collection and analysis, increasing the rate of data collection and analysis, recommending an on-site physical check of the monitored transformer, reducing transformer load, and taking the transformer off line.

Method and apparatus for monitoring transformers

A network protector relay produces a close signal entirely from sequence components based on the magnitude and phase relationships between the positive sequence component of the phase-to-ground voltages on the network side of the protector and the positive sequence component of the phasing voltages. The close signal may be inhibited by either the presence of the negative sequence component of the phase-to-ground voltages on the network side of the protector or if a trip contact is closed. The trip contact will be closed under certain specified conditions which make it advantageous to prevent manual closing of the contacts.

Network protector relay

A network protector relay having trip characteristics which respond not only to the direction of the flow of positive-sequence power through the breaker outwardly of the network but which will respond to unbalanced and simultaneous faults in the feeder network as well. The network protector relay in addition to its tripping characteristics includes closing characteristics which will permit the automatic closing of a breaker only when the phase sequence of the feeder is the same as that of the network, there is a proper phase relationship between the network and feeder and the magnitude of the feeder voltage is such that power flow will be in a direction toward the network.

Growing community of inventors

McKeesport, PA, United States of America

David Robert Smith