Renishaw Plc

Itt Industries, Inc.

International Telephone and Telegraph Corporation

International Standard Electric Corporation

Stc, Inc

David N Batchelder

Chunwei Cheng

Gillies D Pitt

Roger J Williamson

Brian J Smith

Raymond J Chaney

Kurt J Baldwin

Arulanandam M Prabakaran

Jolyon P Willson

Roger E Jones

Rosamund C Neat

Ian P Hayward

Richard J Lacey

G David Pitt

Detector for explosive substances

A sample placed under a microscope is illuminated by light from a laser beam. Raman scattered light is passed back via a dichroic filter to various optical components which analyse the Raman spectrum, and thence to a CCD detector. The optical components for analysing the Raman spectrum include tunable dielectric filters in a filter wheel; a Fabry-Perot etalon; and a diffraction grating. These various components may be swapped into the optical path as desired, for example using movable mirrors, enabling the apparatus to be used very flexibly for a variety of different analysis procedures. Various novel analysis methods are also described.

Spectroscopic apparatus and methods

Spectrum splitting spectroscopic apparatus

In a Raman microscope, Raman scattered light from an illuminated area on a sample 10 is collected by an objective 12 and imaged by a lens 18 onto a detector in an image plane 20. A filter 16 selects only light of a desired Raman wavenumber shift. Since the tuning of this filter is sensitive to the angle of incidence, it is placed after the lens 18 instead of before it, and the distance from the objective 12 to the lens 18 is made substantially equal to the focal length of the lens 18. This ensures that chief rays 14A',14B' from different points on the sample 10 pass through the filter 16 at the same angle of incidence. The wavenumber selected by the filter is therefore the same for light from all points on the sample, which it would not be if the filter were placed before the lens 18.

Raman microscope

A spot of a sample is illuminated by laser light. Raman scattered light is collimated in a parallel beam by a microscope objective, and analyzed by a dispersive or non-dispersive analyzer (such as a diffraction grating or filter). A lens then focuses the Raman scattered light onto a two-dimensional photodetector array in the form of a charge-coupled device (CCD). A confocal technique is described to eliminate light scattered from outside the focal plane of the objective. This may be done by binning together a few pixels of the CCD at the focal point of the lens, or by image processing techniques in a computer.

Raman analysis apparatus

An optical sensor device uses surface plasmon resonance to detect the presence of a specific material. A transparent body (12) is coated with a thin gold film (14) which film may be coated e.g. with an antibody material. The arrangement is illuminated with a divergent light beam and light internally reflected from the gold film is detected by a photodiode array (16). The dielectric conditions adjacent the gold film determine the position of the surface resonance angle, this being indicated by a dark area on the detector array.

Optical surface plasmon sensor device

An arrangement for the remote actuation of a controlled device, e.g. a hydraulic valve, in situations with stringent safety requirements, uses optical power. The optical power, e.g. from a high-power laser, is conveyed via an optical fibre (1) to the controlled device. Here it falls on a heat-absorbent surface (2), as a result of which a volatile fluid (e.g. freon) is evaporated. This via a bellows (4) drives an output rod (5), which operates the controlled device. Alternatives include a bimetallic strip, a thermostat-type capsule, and a memory metal strip, as the heat responsive device.

Optical actuator

In order to determine the vortex shedding frequency, from which the fluid flow rate may be calculated, an optical beam, such as produced by a laser, is passed through a fluid, transversely to a vortex street therein, and modulated in dependence on the alternate high and low velocity regions comprising the vortex street. The modulated signal is detected and 'cleaned' of noise by filtering with a first (high) band-pass filter of a center frequency f.sub.c, such that the first filter output comprises an amplitude modulated signal of carrier frequency f.sub.c modulated by the vortex shedding frequency, that is the frequency of oscillation of the power spectra between the respective curves for the high and low velocity regions. The first filter output is demodulated and filtered by a second (low) band-pass filter, whose output is of a frequency comprising the vortex shedding frequency.

Vortex shedding fluid flowmeter

A vortex flowmeter having a double bluff body arrangement whereby vortices are generated at a rate corresponding to the fluid flow velocity. The upstream body and the downstream body together interact with the fluid stream to generate vortices. The arrangement introduces a relatively low blocking factor in comparison to simple bluff body arrangements. Vortex sensors are located between the bodies and downstream of the second body a distance between three and five times the diameter of that body.

Fluid flowmeter

A bluff body is placed in a fluid pipe with one flat face facing the oncoming fluid. Vortices are then generated and shed alternately from opposite edges of the body. This body is of a scalene triangle cross section, and in one version a hole extends transversely therethrough. A longitudinal hole intersects the first hole at right angles thereto. The vortices cause oscillations in the transverse hole. A light beam is provided in the longitudinal hole. The light beam is modulated as it crosses the path of the transverse hole. Hence by measuring the frequency at which the beam is modulated and by suitable calibration, one gets a good and reliable indication of fluid flow rate. In a second version the transverse hole is formed into a blind hole at the foot of which is an etalon (a Fabry-Perot interferometer). The effect of the fluid oscillations due to vortex generation influences the etalon so that its output is a measure of the fluid flow rate.

Growing community of inventors

London, United Kingdom

David N Batchelder