Ford Global Technolgoies, LLC

Conor Edward Sullivan

Stephen Michael Cicala

Bradley Dean Riedle

Alexander Phillip McDonnell

John Randall Armstead

Dongdong Dee Li

Timothy Fedullo

Charles William Suter

Markian Oleh Diakiw

Yuji Fujii

Hong Jiang

Akshay Bichkar

Jose Velazquez Alcantar

Kurt Howard Nickerson

Richard Reynolds Hathaway

Weitian Chen

Scott Joseph Gittins

Yijing Zhang

Cory Benson Laroche

Thaddeus Hill

Donald G Levens

Ankit Saini

Abhay Mane

Oguz Hasan Dagci

Thirumal Nagadi

Peter Wincek

A vehicle includes an engine, a transmission, and a controller. The engine is configured to generate power to propel the vehicle. The transmission has gears and clutches configured to shift between the gears. The controller is programmed to operate the clutches during wide-open throttle events to upshift the gears at shift points corresponding to engine speeds. The controller is further programmed to adapt the shift points by increasing the shift points over a series of the wide-open throttle events from initial values to mature values.

Shift point adaptation method for a vehicle powertrain

A vehicle includes a powertrain, an inertial measurement unit configured to measure inertial forces exerted onto the vehicle, and a controller. The controller is programmed to control the torque at the powertrain based on a mapped relationship between the inertial forces and a vehicle velocity, wherein the mapped relationship utilizes at least one mapping parameter. The controller is further programmed to estimate a mass of the vehicle based on the mapping parameter.

Vehicle mass calculation and vehicle controls

A vehicle transmission includes a plurality of friction clutches and a selectable one-way clutch. The transmission also includes a controller programmed to, in response to detecting a component fault, switch the selectable one-way clutch from a passive state to an active state by commanding engagement of a first subset of the friction clutches to establish a slip elimination state. The controller is also programmed to, following establishment of the slip elimination state, command the selectable one-way clutch to the active state.

Transmission with selectable one-way clutch

Ideally, when a transmission is in Neutral, no torque should be exerted on the vehicle wheels by the powertrain. However, even with all clutches in a gearbox disengaged, some torque may be transmitted from a turbine shaft to the transmission output due to clutch drag and transmission component inertia. To avoid transmitting torque, a subset of clutches may be engaged to produce an input tie-up state, this holding the turbine shaft against rotation while permitting rotation of the output element.

Method of controlling transmission in neutral

A transmission includes a selectable one-way clutch with active and passive states. Successful transition from the active state to the passive state is only possible when there is no torque tending to cause overrunning. After commanding a transition from the active state to the passive state, a controller partially engages a first friction clutch to induce a torque tending away from overrunning until a lash crossing is detected. Then, the controller releases the first clutch and partially applies a second clutch to induce a torque toward overrunning. When slip is detected, indicating successful achievement of the passive state, the second clutch is released.

A transmission includes a selectable one-way clutch with an active state and a passive state. To avoid occupant discomfort and hardware damage, transitions from the passive state to the active state must only be commanded when no or very little slip is present across the selectable one-way clutch. Several methods are presented to eliminate slip, depending on vehicle speed. When the vehicle is stationary, full engagement of a clutch that causes slip to be proportional to vehicle speed eliminates slip. When the vehicle is moving backwards, partial engagement of the above clutch eliminates slip. When the vehicle is moving forwards, full engagement of all but one clutch of a tie-up condition and partial engagement of the remaining clutch of the tie-up condition brings the vehicle to a stop and eliminates slip.

A vehicle includes a transmission having a torque converter, an oncoming clutch, and a controller. The controller is programmed to, in response to a torque of the oncoming clutch exceeding an estimated average by a threshold during an engagement, increase the torque of the oncoming clutch via a feedforward command and adjust the torque of the oncoming clutch via a feedback command to compensate for deviations in the torque generated by the feedforward command during the engagement.

Vehicle transmission clutch engagement control system

A vehicle includes a transmission having a first neutral with a first combination of engaged clutches and a second neutral with a second combination of engaged clutches. The second neutral has more engaged clutches than the first neutral. A vehicle controller is programmed to, in response to a request to shift from the first to the second neutral and a failed-on clutch being detected, inhibit the shift to remain in the first neutral.

Method and control for operating transmission during clutch failure

A vehicle includes a transmission having a first neutral with a first combination of engaged clutches and a second neutral with a second combination of engaged clutches. The first neutral has more engaged clutches than the second. A controller is programmed to, in response to a request to shift from a drive gear to the first neutral and a clutch of the drive gear being failed-on, shift to the second neutral.

Method and control for operating transmission during clutch failure when shifting from gear to neutral

A transmission includes a first hydraulic clutch, a second hydraulic clutch, a third hydraulic clutch, a pump and a controller. The first, second, and third hydraulic clutches are configured to established a parked-ready condition upon engagement of all three clutches. The pump is configured to generate hydraulic fluid pressure. The controller is programmed to, in response to a command to start an engine that powers the pump, engage the first and second clutches. The controller is further programmed to, in response to engagement of the first and second clutches and obtaining operating hydraulic fluid pressure, engage the third clutch.

Growing community of inventors

Canton, MI, United States of America

Conor Edward Sullivan