Hong Kong Applied Science and Technology Research Institute Company, Limited

Chun Fai Wong

Kwok Kuen (David) Kwong

Kam Hung Chan

Leung Ling (Alan) Pun

Ho Ming (Karen) Wan

Yat Tung Lai

Guangjie Cai

Tai Yin Wong

Kwok Kuen David Kwong

David Kwok Kuen Kwong

Chit Ah Mak

Lap Chi David Leung

Lap Chi (David) Leung

Lap Chi Leung

Xiaofei Kuang

Jennifer Shuet Yan Ho

A single-temperature-point temperature-sensitivity sensor assumes that all sensitivity lines converge at absolute zero temperature, so during calibration measurement is needed at only one temperature. A sensor output voltage is generated by current from a mirrored current source flowing through a variable resistor. During calibration, the resistance of the variable resistor and the mirror ratio of the mirrored current source are adjusted. An error amplifier compares voltages generated by unit currents generated by unit current sources to adjust the unit current sources and the mirrored current source. Each unit current flows through a grounded-base PNP transistor. A switchable PNP transistor is in parallel with one of the grounded-base PNP transistors and has its base switched on and off to adjust the PNP current for two measurements. The difference between the two measurements is compared to a calibration target to adjust the variable resistor and mirror ratio during calibration at a single temperature.

Single-temperature-point temperature sensor sensitivity calibration

A low-headroom current driver does not use an op amp or resistor. A sensing transistor having its source connected to a drain of an output transistor senses variations in an output current. The gate, source, and drain voltages of the sensing transistor are mirrored to a sense mirror transistor to control a sense current. The sense current is mirrored to a reference source transistor to generate a mirrored sense current. An error between the mirrored sense current and a fixed reference current is stored as charge on an error-storing capacitor. The stored error charge creates a negative-feedback compensation current that adjusts a gate voltage generated by a feedback-driving transistor. The adjusted gate voltage controls the gate of the output transistor to compensate for the sensed variation in output current. The sensing current is also compensated using a sense-mirror tail transistor connected to the sense mirror transistor.

Low-headroom constant current source for high-current applications

A differential on-chip temperature sensor circuit can be implemented in a standard complementary metal-oxide-semiconductor (CMOS) process using PNP transistors. A pair of transistors have collector currents that are sensitive to voltage, both directly and due to saturation currents. A scaling resistor connects to the emitter of one transistor and its voltage compared to the other transistor's emitter voltage by an error amplifier that generates a bias voltage to current sources that are proportional to absolute temperature since the saturation current sensitivity is subtracted out. The current is mirrored to sink current through a multiplier resistor from an output. An amplifier connected across the multiplier resistor compares a reference voltage to set the DC bias independent of temperature sensitivity. The temperature sensitivity is proportional to the ratio of the multiplier resistor and the scaling resistor, and is multiplied by a mirroring factor. A differential output is provided.

Differential temperature sensor with sensitivity set by current-mirror and resistor ratios without limiting DC bias

An on-chip temperature sensor circuit can be implemented in a standard complementary metal-oxide-semiconductor (CMOS) process using PNP transistors. A pair of transistors have collector currents that are sensitive to voltage, both directly and due to saturation currents. A scaling resistor connects to the emitter of one transistor and its voltage compared to the other transistor's emitter voltage by an error amplifier that generates a bias voltage to current sources that are proportional to absolute temperature since the saturation current sensitivity is subtracted out. The current is mirrored to sink current through a multiplier resistor from an output. An amplifier connected across the multiplier resistor compares a reference voltage to set the DC bias independent of temperature sensitivity. The temperature sensitivity is proportional to the ratio of the multiplier resistor and the scaling resistor, and is multiplied by a mirroring factor. A differential output may also be provided.

CMOS temperature sensor with sensitivity set by current-mirror and resistor ratios without limiting DC bias

A bridge rectifier operates on low A.C. input voltages such as received by a Radio-Frequency Identification (RFID) device. Voltage drops due to bridge diodes are avoided. Four p-channel transistors are arranged in a transistor bridge across the A.C. inputs to produce an internal power voltage. Another four diode-connected transistors form a start-up diode bridge that generates a comparator power voltage and a reference ground. The start-up diode bridge operates even during initial start-up before the comparator and boost drivers operate. A comparator receives the A.C. input and controls timing of voltage boost drivers that alternately drive gates of the four p-channel transistors in the transistor bridge with voltages boosted higher than the peak A.C. voltage. Substrates are connected to the power voltage on the power-voltage half of the bridge and to the A.C. inputs on the ground half of the bridge to fully shut off transistors, preventing reverse current flow.

Diode-less full-wave rectifier for low-power on-chip AC-DC conversion

A motor driver circuit for driving the gate node of a high-side driver transistor to a boosted voltage from a charge pump draws little or no static current from the charge pump. The gate node is pulled to the boosted voltage by a p-channel pullup-control transistor that is driven by p-channel transistors that are pumped by capacitors that cut off current flow to ground from the charge pump. An n-channel output-shorting transistor shorts the gate node to the output when the high-side driver is turned off. A coupling capacitor initializes the shorting transistor for each output transition. A p-channel output-sensing transistor generates a feedback to a second stage that drives the coupling capacitor. P-channel diode transistors and an n-channel equalizing transistor control the voltage on the coupling capacitor.

Bootstrapped high-side driver control without static DC current for driving a motor bridge circuit

A Optical Black Pixel (OBP) cancellation circuit corrects offsets in sensors in a CCD/CMOS image sensor when reading dark pixels such at the periphery. A pixel voltage is switched to a sampling capacitor during two phases of the same pixel pulse. Sampling capacitors and feedback capacitors connect to differential inputs of an amplifier. An accumulating capacitor accumulates voltage differences and generates a common-mode voltage that is fed back to another sampling capacitor that stores an amplifier offset. The sampling capacitor and accumulating capacitor and their associated switches form a discrete-time first-order low-pass filter that filters the pixel voltage during the first phase. In the second phase the amplifier acts as a unity-gain amplifier to output an average of the pixel voltage differences generated during an OBP time when blackened or covered pixels are read from the image sensor.

Optical black-level cancellation for optical sensors using open-loop sample calibration amplifier

A gain control circuit including a resistor with a first terminal and a second terminal; an operational amplifier with an inverting terminal thereof electrically coupled to said first terminal of said resistor; a non-inverting terminal thereof; and an output terminal thereof; an amplifier circuit for transforming the voltage change of said operational amplifier output into a substantially exponential current change; wherein the output of said amplifier circuit is electrically coupled to said inverting terminal of said operational amplifier. The above described gain control circuit is able to perform wide bandwidth input signal buffering with linearity under low voltage and low power conditions. The circuit also offers low output impedances without the need of additional buffers and hence minimizing circuit size and manufacturing costs.

Growing community of inventors

Hong Kong, China

Chun Fai Wong