Capstone Turbine Corporation

Brian W Peticolas

Everett R Geis

Joel B Wacknov

Robert W Bosley

Edward C Edelman

Steven W Lampe

A turbogenerator/motor controller with a microprocessor based inverter having multiple modes of operation. To start the turbine, the inverterconnects to andsupplies fixed current, variable voltage, variable frequency, AC power to the permanent magnet turbogenerator/motor, driving the permanent magnet turbogenerator/motor as a motor to accelerate the gas turbine. During this acceleration, spark and fuel are introduced in the correct sequence, and self-sustaining gas turbine operating conditions are reached. The inverter is thendisconnected from the permanent magnet generator/motor,reconfigured to a controlled 60 hertz mode, and then either supplies regulated 60 hertz three phase voltage to a stand alone load or phase locks to the utility, or to other like controllers, to operate as a supplement to the utility. In this mode of operation, the power for the inverter is derived from the permanent magnet generator/motor via high frequency rectifier bridges. The microprocessor monitors turbine conditions and controls fuel flow to the gas turbine combustor.

Turbogenerator/motor controller

A power control system for a turbogenerator which provides electrical power to one or more pump-jack oil wells. When the induction motor of a pump-jack oil well is powered by three-phase utility power, the speed of the pump-jack shaft varies only slightly over the pumping cycle but the utility power requirements can vary by four times the average pumping power. This power variation makes it impractical to power a pump-jack oil well with a stand-alone turbogenerator controlled by a conventional power control system. This power control system comprises a turbogenerator inverter, a load inverter, and a central processing unit which controls the frequency and voltage/current of each inverter. Throughout the oil well's pumping cycle, the central processing unit increases or decreases the frequency of the load inverter in order to axially accelerate and decelerate the masses of the down hole steel pump rods and oil, and to rotationally accelerate and decelerate the masses of the motor rotors and counter balance weights. This allows kinetic energy to be alternately stored in and extracted from the moving masses of the oil well and allows the oil pumping power to be precisely controlled throughout the pumping cycle, resulting in a constant turbogenerator power requirement.

Turbogenerator power control system

A power control system for a turbogenerator which provides electrical power to pump-jack oil well. When the induction motor of a pump-jack is powered by three-phase utility power, the speed of the shaft varies only slightly over the pumping cycle but the utility power requirements can vary by four times the average pumping power. This variation makes it impractical to power a pump-jack oil well with a stand-alone turbogenerator controlled by a conventional power control system. This control system comprises a turbogenerator inverter, a load inverter, and a central processing unit which controls the frequency and voltage/current of each inverter. Throughout the pumping cycle, the processing unit increases or decreases the frequency of the load inverter in order to axially accelerate and decelerate the masses of the down hole pump rods and oil, and to rotationally accelerate and decelerate the motor rotors and counter balance weights. This allows kinetic energy to be alternately stored in and extracted from the moving masses of the oil well and allows the pumping power to be precisely controlled, resulting in a constant turbogenerator power requirement.

A turbogenerator/motor controller with a microprocessor-based control system having a synchronous condenser, line commutated inverter, and a battery coupled to the turbogenerator/motor controller. When a load transient occurs, the gas turbine engine and the synchronous condenser, which draws its power from the line commutated inverter and battery, provide the power required to successfully meet the transient until the gas turbine engine controls respond by commanding the gas turbine engine to a higher speed, producing more power out of the turbogenerator. In the event of a sudden reduction in load, an auxiliary load device temporarily draws load until the gas turbine engine controls can respond and reduce the output power of the turbogenerator.

Turbogenerator/motor control with synchronous condenser

A permanent magnet generator having a winding split into two equal windings with each of the two windings connected to a separate three phase rectifier block of a pulse width modulated inverter The pulse width modulated inverter includes three (3) IGBT channels across the voltage bus with the neutral created between the separate three phase rectifier blocks.

Split generator winding inverter

A turbogenerator/motor controller with a microprocessor based inverter having multiple modes of operation with an energy storage and discharge system including an ancillary electric storage device, such as a battery, connected to the generator controller through control electronics. Electrical energy can flow from the ancillary electric storage device to the turbogenerator controller during start up and increasing load and vice versa during self-sustained operation of the turbogenerator. When utility power is unavailable, the ancillary electric storage device can provide the power required to start the turbogenerator. When a load transient occurs, the gas turbine engine and the ancillary electric storage device provide the power required to successfully meet the transient.

Turbogenerator/motor controller with ancillary energy storage/discharge

A controller for a permanent magnet turbogenerator/motor having a pulse width modulated inverter and a rectifier bridge. The pulse width modulated inverter includes a positive section magnetic winding and a separate equal negative section magnetic winding, and the inverter has a positive section connected to the positive section magnetic winding of the pulse width modulated inverter and a negative section connected to the separate negative section magnetic winding of the pulse width modulated inverter.

Turbogenerator/motor pulse width modulated controller

A turbogenerator/motor controller with a microprocessor based inverter having multiple modes of operation. To start the turbine, the inverter connects to and supplies fixed current, variable voltage, variable frequency, AC power to the permanent magnet turbogenerator/motor, driving the permanent magnet turbogenerator/motor as a motor to accelerate the gas turbine. During this acceleration, spark and fuel are introduced in the correct sequence, and self-sustaining gas turbine operating conditions are reached. The inverter is then disconnected from the permanent magnet generator/motor, reconfigured to a controlled 60 hertz mode, and then either supplies regulated 60 hertz three phase voltage to a stand alone load or phase locks to the utility, or to other like controllers, to operate as a supplement to the utility. In this mode of operation, the power for the inverter is derived from the permanent magnet generator/motor via high frequency rectifier bridges. The microprocessor monitors turbine conditions and controls fuel flow to the gas turbine combustor.

Growing community of inventors

Redondo Beach, CA, United States of America

Brian W Peticolas