Xerox Corporation

Barbara D Ceglinski

Robert F Dunham

Warren R Smith

Mark Muscato

Edouard E Langlois

Alan C Kirchoff

Kathryn T Kehoe

Michael D Stair

Edward F Grabowski

Satchidanand Mishra

Anthony M Horgan

Robert C Yu

Bing R Hsieh

Michael Stephen Roetker

Kent J Evans

Richard L Post

Donald C VonHoene

John J Darcy

Karl V Thomsen

Timothy J Leenhouts

Leonard F Quinn

Richard A Cairncross

A process for treating a seamed flexible electrostatographic imaging belt including providing an imaging belt including at least one layer including a thermoplastic polymer matrix and a seam extending from one edge of the belt to the other, providing an elongated support member having a arcuate supporting surface and mass, the arcuate surface having at least a substantially semicircular cross section having a radius of curvature of between about 9.5 millimeters and about 50 millimeters, supporting the seam on the arcuate surface with the region of the belt adjacent each side of the seam conforming to the arcuate supporting surface of the support member with a wrap angle at least sufficiently enough to provide arcuate support for the seam area, traversing the seam from one edge of the belt to the other with infrared rays from a tungsten halogen quartz bulb focused with a reflector having a hemiellipsoid shape to form a heated substantially circular spot straddling the seam during traverse, the spot having a diameter of between about 3 millimeters and about 25 millimeters, without exceeding the breadth of supported arcuate seam area, to substantially instantaneously heat the thermoplastic polymer matrix in the seam and the region of the belt adjacent each side of the seam directly under the heating spot to at least the glass transition temperature of the polymer matrix without significantly heating the support member, and rapidly quenching the seam by thermal conduction of heat from the seam to the mass of the support member to a temperature below the glass transition temperature of the polymer matrix while the region of the belt adjacent each side of the seam conforms to the arcuate supporting surface of the support member. Apparatus for carrying out this process is also disclosed.

Seam stress release in flexible electrostatographic imaging belts

A dryer with zone temperature controls for drying thick polymer-solvent layers on a substrate. The dryer is formed with several heating elements located in an air duct. The cool air is heated a specific amount as it passes each heating element. The heated air is then applied to the polymer-solvent solution on the substrate in a continuous fashion so that the polymer-solvent solution slowly heats up as it passes through the drying apparatus. The preferred design is to ensure a zone residence time of less than 10 seconds and a web heating rate of 10.degree. F./second or less. Most preferred design is a zone residence time less than 5 seconds and a heating rate less that 5.degree. F./second. The dryer is designed to have a continuous temperature gradient, especially in the critical later stages of drying when the solvent content of the film is less than 20%.

Method and apparatus for a mechanical dryer for drying thick polymer

Apparatus for the continuous coating of charge transport solutions onto a substrate to form an electrophotographic imaging member, including a pump to a flow of a first highly doped charge transport solution and a pump to a flow of a second undoped or lowly doped charge transport solution at predetermined rates to a common junction at which the flows intermix into a common flow upon contacting each other; piping connecting the pumping means to the common junction; and mixing device associated with the junction for continuously mixing the common flow during its movement through the mixing device, the mixing device having a short spiral flow path of less than about 200 cm for the solutions sufficient to substantially complete mix the common flow during its movement through the mixing means.

Fabrication of electrophotographic imaging members

Processes and apparatus for fabricating an electrophotographic imaging member in which a web coated with a charge generation layer is coated with a charge transport layer comprising a dopant, the improvement comprising detecting the change in dopant concentration required, determining the amount of highly doped charge transport composition and amount of undoped or lowly doped charge transport composition required to achieve the change in dopant concentration, feeding the determined amounts of highly doped charge transport composition and undoped or lowly doped charge transport composition into a mixing zone, rapidly mixing the amounts of highly doped charge transport composition and undoped or lowly doped charge transport composition to form a uniformly doped charge transport composition, and applying the uniformly doped charge transport composition to the charge generation layer.

Growing community of inventors

Oklahoma City, OK, United States of America

Barbara D Ceglinski