Industrial Technology Research Institute

Bao-Shun Yau

Su-Tsai Lu

Chih-Chiang Lu

Sheng-Feng Chung

Chung-Huang Huang

Mike Lu

Wen-Yung Yeh

Chun-Ting Liu

Chen-Kun Chen

Kuo-Hua Tseng

Yi-Ming Chang

Cheng-Yi Shih

Heng-Tien Lin

Shu-Yi Chang

Yu-Ling Hsieh

Cheng-Yi Chiang

A sensing structure includes a sensing unit, a periphery circuit, and a connecting circuit. The connecting circuit connecting the sensing unit and the periphery circuit includes a connecting pattern. In an embodiment, the connecting pattern has at least two line widths. The line width of a part of the connecting pattern connecting the periphery circuit is greater than the line width of a part of the connecting pattern connecting the sensing unit. In an embodiment, the connecting pattern includes a mesh pattern having at least two mesh densities. The mesh density of a part of the mesh pattern connecting the periphery circuit is greater than the mesh density of a part of the mesh pattern connecting the sensing unit. In an embodiment, the connecting circuit includes lines between and connecting a single sensing series of the sensing unit and a periphery wire of the periphery circuit.

Sensing structure

An illumination device includes an OLED panel, an electrode structure, and a control module. The OLED panel includes a light-emitting layer configured to emit a light beam. The electrode structure is overlaid on the OLED panel. The electrode structure includes a first touch electrode including at least two conductive portions, and the conductive portions of the first touch electrode are electrically connected to the other conductive portions. The control module is electrically connected to the OLED panel and the first touch electrode. The light-emitting layer further includes a light-emitting material, and a width of the light-emitting material is greater than half of a width of the first touch electrode.

Illumination device

A solar cell module is described, including a series of solar cells each including a bottom electrode, a photoelectric conversion layer, an insulating pattern, a top electrode layer and a passivation layer. The conversion layer is on the bottom electrode and also on the substrate at a first side of the bottom electrode. The insulating pattern is on the bottom electrode, covering an edge portion of the conversion layer near a second side of the bottom electrode. The top electrode layer is on the conversion layer and adjacent to the insulating pattern. The passivation layer is on the top electrode layer and adjacent to the insulating pattern, wherein the top of the passivation layer on the top electrode layer is lower than the top of the insulating pattern. The bottom electrode of a solar cell is electrically connected with the top electrode layer of an adjacent solar cell.

Solar cell module and solar cell

A touch structure and a manufacturing method for the same are provided. The touch structure comprises first patterned electrodes, a second patterned electrode, a dielectric structure and a conductive bridge. The second patterned electrode is disposed between the first patterned electrodes, and separated from the first patterned electrodes. The dielectric structure is disposed on the first patterned electrodes and the second patterned electrode. The dielectric structure has a dielectric opening. The conductive bridge is disposed across the dielectric structure and extended in the dielectric opening. The first patterned electrodes are electrically connected to each other through the conductive bridge.

Touch structure and manufacturing method for the same

A flexible projective capacitive touch sensor structure includes following elements. A roll of first flexible transparent substrate has sensing unit regions thereon, and each of the sensing unit regions includes at least two first transparent patterned electrodes and at least three second transparent patterned electrodes. Bridging wires respectively stride over the corresponding first transparent patterned electrodes and respectively and electrically bridge the second transparent patterned electrodes located at two sides of each of the first transparent patterned electrodes to form at least one conducting wire. Dielectric pads are disposed between the bridging wires and the first transparent patterned electrodes. First connection wires are connected to the first transparent patterned electrodes and have first electrical connection terminals. Each of the second connection wires is connected to one second transparent patterned electrode of one end of the at least one conducting wire and has one second electrical connection terminal.

Flexible projective capacitive touch sensor structure

A projective capacitive touch sensor structure includes following elements. Two second transparent patterned electrodes are disposed on a substrate and located at two sides of a first transparent patterned electrode. A bridging wire strides over the first transparent patterned electrode and electrically bridges the second transparent patterned electrodes to form a conducting wire. A transparent dielectric pad is disposed between the bridging wire and the first transparent patterned electrode. A dielectric portion of the transparent dielectric pad located above the first transparent patterned electrode and the second transparent patterned electrodes includes an upper surface, a lower surface and an inclined side surface connecting the upper surface and the lower surface, an area of the upper surface is 70%-95% of an area of the lower surface, and an included angle between the inclined side surface and the lower surface is an acute angle.

Projective capacitive touch sensor structure and fabricating method thereof

A touch panel roll and a manufacturing method thereof are provided. The method includes providing a first structure roll and a second structure roll. A manufacturing method of the first structure roll includes forming an opening in a first flexible substrate, wherein conductive lines respectively connected with electrodes extend to the opening. A manufacturing method of the second structure roll includes forming conductive lines respectively connected with electrodes and independent conductive lines corresponding to the conductive lines in the first structure roll on a second flexible substrate, wherein one end of each conductive line in the second structure roll is located at a position corresponding to the opening. The method further includes laminating the first structure roll and the second structure roll by a roll-to-roll process.

Growing community of inventors

Kaohsiung, Taiwan

Bao-Shun Yau