Other

University of Texas System

James N. Mccoy

Augusto L Podio

James N McCoy

Jerry B West

Kamy Sepehrnoori

Kenneth L Huddleston

Paulo M Carvalho

Dieter J Becker

Orvel Lynn Rowlan

James W Jennings

A production system and method for producing fluids from a well are presented. The production system may include a submersible pump and a jet pump. The submersible pump may be arranged within the well. The jet pump may be arranged within the well downstream of the submersible pump. The jet pump may include a power fluid intake configured to receive a power fluid and a produced fluid intake configured to receive a produced fluid. The power fluid intake may be in fluid communication with the submersible pump. The produced fluid intake may be in fluid communication with gas within the well. In an embodiment, the produced fluid intake may be in fluid communication with separated gas within an annulus of the well. Beneficially, the system may allow, among other things, a submersible pump and a jet pump to be used in combination in high gas-liquid-ratio wells without installing a gas vent line.

Production system and method for producing fluids from a well

Plunger lift operations are difficult to optimize due to lack of knowledge of tubing pressure, casing pressure, bottom-hole pressure, liquid accumulation in the tubing and location of the plunger. Monitoring the plunger position in the tubing helps the operator (or controller) to optimize the removal of liquids and gas from the well. The plunger position can be tracked from the surface by monitoring acoustic signals generated as the plunger falls down the tubing. When the plunger passes by a tubing collar recess, an acoustic pulse is generated that travels up the gas within the tubing. The acoustic pulses are monitored at the surface, and are converted to an electrical signal by a microphone. The signal is digitized, and the digitized data is stored in a computer. Software processes this data along with the tubing and casing pressure data to display plunger depth, plunger velocity and well pressures vs. time. Plunger arrival at the liquid level in the tubing and plunger arrival at the bottom of the tubing are identified on the time plots. Inflow performance is calculated. Software displays the data and analysis in several formats including a graphical representation of the well showing the tubing and casing pressures, plunger location, gas and liquid volumes and flow rates in the tubing and annulus, and inflow performance relationship at operator selected periodic intervals throughout the cycle. Several field cases are presented to show how this information is applied to optimization of plunger lift operations.

Determination of plunger location and well performance parameters in a borehole plunger lift system

A downhole gas separator is connected to the lower end of a tubing string. The separator includes a tubular body which has a decentralizer mounted to one side for driving the opposite side of the separator against an interior wall of the casing. This creates a narrow flow zone between the separator body and the adjacent casing wall and a wider flow zone on the decentralizer side of the body. A fluid inlet is provided on the side of the gas separator tubular body facing the narrow flow zone. The fluid in the narrow flow zone has a substantially higher concentration of liquid than the fluid in the wider flow zone. Fluid, primarily liquid, flows through the fluid inlet into a chamber within the separator. A dip tube transfers the fluid from the separator chamber to the pump.

Downhole gas separator

An oil well pumping unit has a walking beam which raises and lowers a rod connected to a downhole pump. To perform well analysis, it is desirable to know the position of the rod during the stroke. An accelerometer is mounted on the pumping system unit to move in conjunction with the rod. An output signal from the accelerometer is digitized and provided to a portable computer. The computer processes the digitized accelerometer signal to integrate it to first produce a velocity data set and second produce a position data set. Operations are carried out to modify the signal and produce a position trace with stroke markers to indicate positions of the rod during its cyclical operation.

Method and apparatus for measuring pumping rod position and other

In a pumping well, oil is normally lifted to the surface by a rod which extends from the surface to a downhole pump. A transducer is attached to the rod at the surface to sense the deformation, i.e., the change in diameter or circumference of the rod to determine change in rod loading. The transducer includes strain gauges which produce output signals proportional to the change in the diameter or circumference of the rod which occurs due to changes in load on the rod. The transducer may also include an accelerometer. The change in load on the polished rod over a pump cycle is used in conjunction with data produced by the accelerometer to calculate a downhole card. The downhole card showing change in pump load is adjusted to reflect absolute rod load by determining an appropriate offset. Various ways to determine the offset are available. Since the pump plunger load is zero on the downstroke when the traveling valve is open, the value necessary to correct the calculated minimum pump value to a zero load condition may be used as the offset. The offset can also be estimated by either a calculation of the rod weight, a predetermined rod weight measurement or an estimated load value by the operator.

Method of using a polished rod transducer

An echo sounding system includes an acoustic gun which is mounted to the wellhead of a borehole. The acoustic gun produces an acoustic pulse which is transmitted down the borehole. A tubing string is installed in the borehole and it has substantially evenly spaced collars. Fluid is pumped from the borehole, or well, by use of a reciprocating pump driven by a pump rod extending to the surface. The acoustic pulse produces reflections when it strikes the tubing collars and the surface of the fluid. A microphone detects the reflections to produce a return signal. This signal is digitized and stored. The digitized signal is processed to detect the rate of the collar reflections and the stored signal is narrowband filtered with a passband filter centered at the rate of receipt of the collars. Each cycle of the narrowband filtered signal corresponds to one collar reflection. In this signal, each cycle is counted, and extrapolation used when necessary to produce a collar count extending from the surface to the liquid surface. This is multiplied by the average joint length to produce the depth to the liquid surface. The system further detects the liquid level and displays it as a marker on the data signal. An operator can use the automatically determined marker or move it to another position. Finally, the operator is provided with optimum operating parameters for achieving maximum production from the well.

Method for processing echo sounding data collected from boreholes in the

An echo sounding system includes a acoustic gun which is mounted to the wellhead of a borehole. The acoustic gun produces a acoustic pulse which is transmitted down the borehole. A tubing string is installed in the borehole and it has substantially evenly spaced collars. Fluid is pumped from the borehole, or well, by use of a reciprocating pump driven by a pump rod extending to the surface. Fluid is received from a surrounding formation and collects in the borehole. The acoustic pulse produces reflections when it strikes the tubing collars and the surface of the fluid. A microphone detects the reflections to produce a return signal. This signal is digitized and stored. The digitized signal is processed to detect the rate of the collar reflections and the stored signal is narrowband filtered with a passband filter centered at the rate of receipt of the collars. The data signal is further processed to determine the time of occurrence of the acoustic pulse and the liquid surface reflection. Each cycle of the narrowband filtered signal corresponds to one collar reflection. In this signal, each cycle is counted, and extrapolation used when necessary to produce a collar count extending from the surface to the liquid surface. This is multiplied by the average joint length to produce the depth to the liquid surface. The data signal and various well parameters and a schematic of the well are displayed for use by an operator. The system further detects the liquid level and displays it as a marker on the data signal. An operator can use the automatically determined marker or move it to another position. Finally, the operator is provided with optimum operating parameters for achieving maximum production from the well.

Growing community of inventors

Austin, TX, United States of America

Augusto L Podio