Sms Group Gmbh

August Sprock

Christoph Hassel

Johannes Alken

Wolfgang Fuchs

Ulrich Cramer

Thomas Heimann

Heinz-Juergen Oudehinken

Henning Berg

Carsten Andreas Klein

Heinz-Jürgen Oudehinken

Jens Kiessling-Romanus

Kai Grybel

Guido Buschhoff

Thomas Meyer

Alexander Boushmelev

Anne-Marie Fontayne

A method for controlling or regulating the temperature of a steel strip in hot forming in a hot strip mill. A superordinate open-loop or closed-loop controller has a process model that predetermines the temperature development of the hot strip. The target values of the individual units are adjusted based on this predetermined temperature development.

Method for the open-loop or closed-loop control of the temperature of a steel strip during hot working in a hot strip mill

A method for controlling a cooling device which is set up to control temperature of a rolling stock such as a metal strip, which runs through a cooling device along a conveying direction of a rolling train. The cooling device is arranged upstream of the rolling train. The method includes determining total enthalpy of a system formed by the rolling stock; determining a measure for the formation of scale, which includes a scale factor that depends on chemical composition and surface temperature of the rolling stock, and a heat transfer coefficient of the scale; calculating a temperature distribution and/or average temperature in the rolling stock based on a temperature calculation model, in which the determined total enthalpy and the measure for the formation of scale are included; and setting a cooling capacity of the cooling device taking into account the calculated temperature distribution and/or average temperature in the rolling stock.

Method for controlling a cooling device in a rolling train

A method for producing a metallic strip or sheet, in which the strip or sheet is rolled in a multi-stand rolling mill and is discharged downstream of the last roll stand of the rolling mill in a conveying direction. The strip or sheet is cooled in the multi-stand rolling mill and/or downstream of the rolling mill as viewed in the conveying direction, wherein a temperature of the strip or sheet is measured upstream of the last roll stand of the rolling mill as viewed in conveying direction. Based on this measured temperature, a temperature for the strip or sheet at the exit of the last roll stand of the rolling mill is then determined by calculation with the aid of a temperature calculation model, with which further temperature processes of the manufacturing method can be controlled or regulated after a comparison with a predetermined reference value.

Process for the production of a metallic strip or sheet

A method for setting different cooling rates of metal strips or metal plates (rolling material) over the strip width of a cooling stretch in a hot-strip mill or heavy-plate mill is presented. According to the method, for the calculation of the cooling rate, the initial enthalpy distribution over the material width of the rolling material before the cooling is determined. Proceeding therefrom, a target enthalpy distribution is determined in the width direction and length direction of the rolling material while taking into account a calculation of the flatness and the mechanical properties by means of a microstructure model. Subsequently, the coolant amount and the coolant curve of the cooling stretch are set.

Method for setting different cooling curves of rolling material over the strip width of a cooling stretch in a hot-strip mill or heavy-plate mill

A cooling group for a laminar cooling device, including at least one cooling unit arranged above and below a strip to be cooled in order to supply the strip with a cooling liquid, including a central inlet via which cooling liquid is supplied, a distributing tube supplied with cooling liquid by the central inlet, and a number of supplying units supplied with cooling liquid from the distributing tube. Each supplying unit has a number of cooling nozzles via which cooling liquid is discharged onto the strip. In order to minimize the influence of the number of supplying units which are switched on or switched off, and thus have as little expenditure as possible, a volumetric flow rate regulating valve is arranged in or in front of the central inlet. The regulating valve is used to conduct a defined volume of cooling liquid through the central inlet per unit of time.

Cooling unit of a laminar cooling device

A cooling device for cooling a metallic item and a method for operating the cooling device. Such cooling devices having a plurality of cooling bars arranged in parallel in groups for applying a coolant to the metallic item are known in the prior art. In order to be able to set a desired distribution function of the coolant over the width of the metallic item as precisely as possible, the cooling device provides that similar application regions in at least two cooling bars within a group are each formed differently with respect to their contour and/or with respect to their surface area.

Cooling device and method for operating same

A method for producing a metal strip, in which the strip is rolled in a multi-stand rolling mill, is removed behind the final rolling stand of the rolling mill in the direction of conveyance, and is cooled in a cooling device. The strip or metal sheet is subjected to additional rapid cooling immediately after passing the working rollers of the final rolling stand, wherein the strip or the metal sheet is cooled at least partially within the extent of the final rolling stand in the direction of conveyance, wherein rapid cooling is performed by applying a coolant to the strip or metal sheet from above and from below, wherein the volume flow of coolant that is applied to the strip or metal sheet from below measures at least 120% of the volume flow of coolant that is applied to the strip or metal sheet from above.

Growing community of inventors

Düsseldorf, Germany

August Sprock