International Business Machines Corporation

Globalfoundries Inc.

Lenovo (singapore) Pte. Ltd.

Arvind Kumar Sinha

Phillip V Mann

John Lee Colbert

Joseph Paul Kuczynski

Kevin O'Connell

Bret Peter Elison

Roger Duane Hamilton

Mark David Plucinski

Sandra J Shirk/Heath

Karl Stathakis

Eric Vance Kline

William James Anderl

John Saunders Corbin, Jr

Kevin Albert Splittstoesser

Kory W Weckman

Timothy Jerome Tofil

Arden Lot Moore

Amanda Elisa Ennis Mikhail

Danny E Massey

Mark Kenneth Hoffmeyer

Michael Robert Rasmussen

Brian Samuel Beaman

Eric Alan Eckberg

Paul N Krystek

Theron Lee Lewis

Maurice Francis Holahan

Stephen M Zins

Michael J Ellsworth, Jr

Levi A Campbell

John Richard Dangler

Phillip Duane Isaacs

Amanda Elisa Mikhail

Gerald Keith Bartley

William Louis Brodsky

Roger Donell Weekly

Scott Alan Shurson

Charles Luther Johnson

Jason R Eagle

Justin Christopher Rogers

Mark Garrison Clark

David R Motschman

Jason Thomas Stoll

Amanda E E Mikhail

Charles C Stratton

John E Kelly, Iii

Thomas S Thompson

Sri Muthuthamby Sri-Jayantha

Vijayeshwar Das Khanna

Martin Joseph Crippen

Christopher Lee Tuma

Pat Gallarelli

Paul Alan Vermilyea

Terry Leo Sobotta

Benjamin Michael Kreuz

Gregory Scott Vande Corput

Nathan Carl Mandelko

Timothy A Tofil

Jason Rodney Eagle

John Saunders Corbin Jr

A heat pipe includes one or more reservoirs of liquid that are closed at lower temperatures and open at higher temperatures. The opening of the reservoirs at higher temperatures caused by higher power levels dynamically increases the amount of liquid in the heat pipe, which increases performance of the heat pipe at higher power levels. As the heat pipe cools, the liquid condenses and flows back into the reservoirs. As the heat pipe continues to cool, the reservoirs close. The result is a heat pipe that is more efficient at lower power levels and still maintains high efficiency at higher power levels due to the demand-based charging of the liquid based on temperature.

Demand-based charging of a heat pipe

A method and system for a dynamic keying system is disclosed. The method and system can include a male connector device having a first plurality of settings for one or more key features, and a female connector device having a second plurality of settings for one or more key features. The female connector device can be configured to operate in an initial mode in which it is configured to, in response to the introduction of the male connector device, correspond a first setting of the first plurality of settings to a second setting of the second plurality of settings. The female connector device can also be configured to operate in a subsequent mode, in which it can permit coupling with at least one male connector device having the first setting and consistently deny access to at least one male connector device having a third setting different than the first setting.

Dynamic keying assembly

Embodiments relate to an apparatus for rework of a BGA package. Memory shape material is placed adjacent to a plurality of solder joints of the package. Stimulation is applied to the material, with the stimulation causing the material to change from a non-stimulated shape to a stimulated shape. This stimulation causes an expansion of the material. As the material expands, it exerts a tensile force on the BGA package and an adjacently positioned carrier, causing a separation of the two components, while mitigating collateral heat of adjacently positioned components.

Ball grid array rework

In an example, a method includes storing thermoset resin rheology data associated with a thermoset resin at a memory. The thermoset resin rheology data includes a plurality of sets of dynamic fluid flow properties that are measured for the thermoset resin. The method includes receiving, at a computing device, information associated with a printed circuit board (PCB) laminate design. The method also includes receiving, at the computing device, a first set of PCB lamination parameters. The method further includes storing, at the computing device, a first thermoset resin flow model. The first thermoset resin flow model is generated based on the thermoset resin rheology data, the information associated with the PCB laminate design, and the first set of PCB lamination parameters.

Thermoset resin flow models for printed circuit board laminates

A heat pipe includes a reservoir of liquid that is connected to a horizontal portion of the heat pipe via a capillary connection. The heat pipe includes a temperature sensor in proximity to a heat interface in the horizontal portion and a controller that controls a heater for the reservoir. As power into the heat pipe increases, the controller turns on the heater, causing the temperature of the liquid in the reservoir to rise. Liquid then passes from the reservoir through the capillary connection into the horizontal portion, thereby dynamically increasing the amount of liquid in the heat pipe, which increases performance of the heat pipe at higher power levels. When the heater is off, as the heat pipe cools, the liquid condenses and flows back through the capillary connection into the reservoir. The result is a heat pipe that provides demand-based charging of the liquid based on power level.

An electronic module is provided in which a chip is disposed over a substrate and electrically connected to the substrate by a plurality of electrical connect structures disposed between the chip and the substrate. A heat distributor, fabricated of a thermally conductive material, is disposed between the chip and the substrate and sized to extend beyond an edge of the chip to facilitate conduction of heat laterally out from between the chip and substrate. The heat distributor includes openings sized and positioned to allow the electrical connect structures to pass through the heat distributor without electrically contacting the heat distributor. The heat distributor is electrically isolated from the electrical connect structures, the chip and the substrate. In one implementation, the heat distributor physically contacts a thermally conductive enclosure of the electronic module to facilitate conduction of heat from between the chip and substrate to the enclosure.

Electronic module with laterally-conducting heat distributor layer

Embodiments relate to a method and apparatus for rework of a BGA package. Memory shape material is placed adjacent to a plurality of solder joints of the package. Stimulation is applied to the material, with the stimulation causing the material to change from a non-stimulated shape to a stimulated shape. This stimulation causes an expansion of the material. As the material expands, it exerts a tensile force on the BGA package and an adjacently positioned carrier, causing a separation of the two components, while mitigating collateral heat of adjacently positioned components.

An apparatus for cooling an electrical heat source is disclosed. A heat exchanger has two principal sub-assemblies. A closed-loop fluid flow is provided through a second sub-assembly, disposed next to a heat source. An open-loop fluid flow is provided though a first sub-assembly in communication with a second sub-assembly. Each of the first and second sub-assemblies has a rotational element. The fluid flow entering the first sub-assembly rotates the first rotational element, and magnetic communication between the rotational elements causes movement of the second rotational element, thereby achieving fluid movement within the second sub-assembly. Operationally, the closed-loop sub-assembly removes heat from the heat source and transfers it to the open-loop sub-assembly for subsequent heat transfer in a downstream fluid flow.

Dual magnetically coupled rotor heat exchanger

An apparatus includes a component bay having an operational height and an expanded height. The component bay is moveable between the operational height and the expanded height. A thermal element divides the component bay into one or more compartments, each compartment configured to receive a system component. The component bay at the operational height provides thermal contact between the received system component and the thermal element.

Method for containing computer system components

According to embodiments of the invention, an electronic component assembly may be provided. The electronic component assembly may include an electronic component body. The electronic component assembly may also include one or more elastic members affixed to the electronic component body. The electronic component assembly may also include a catch mechanism affixed to each elastic member adapted to allow insertion of the elastic member and the catch mechanism through a hole of a circuit board in an extended position, and upon release from the extended position, hold the electronic component body in a fixed position by the tension of the elastic member and the catch mechanism grasping an edge of a surface of the circuit board opposite a surface upon which the electronic component body rests.

Method of affixing a group of elastic filaments to an electronic component body

Growing community of inventors

Rochester, MN, United States of America

Arvind Kumar Sinha