At&t Bell Laboratories

Other

Lucent Technologies Inc.

At+t Corp.

At&t Laboratories, Limited

Anthony J Serafino

Gary J Grimes

Richard J Coyle, Jr

George J Shevchuk

Lawrence J Haas

Lee L Blyler

Charles J Sherman

Lee Landis Blyler, Jr

Ami Kestenbaum

Richard James Coyle, Jr

Finishing an end of a plastic optical fiber by ablating the end of the plastic optical fiber by utilizing an Excimer laser so that the end of the optical fiber can be used in a optical connector. A high powered ultraviolet beam of light from the laser is absorbed by the end of the fiber and ablates the first few microns of the end face of the fiber. This process removes residual cracks and fissures to flatten the end of the fiber for use in the optical connector. The optical fiber is then ready to make a low loss interface with a source, a detector, or another optical fiber.

End finishing of plastic optical fibers using laser ablation

Replacing costly electro-optic or fused quartz crystalline structures or molded plastic optical waveguide splitters with an optical switch comprising an array of spatial light modulators between two relatively, thick, optical glass flats. Associated with each spatial light modulator are partial holes in the optical glass flats with the partial holes being in alignment with the spatial light modulator. Using a new experimentally-developed laser technique, these holes can be drilled to a precise depth so that the distance between the ends of standard silica optical fibers inserted into opposing holes approximates the diameter of those fibers. Since the diameter of a partial hole is insignificant compared to the overall area of an optical glass flat, the physical strength of the optical glass flats is not reduced even when a number of partial holes are drilled into the optical glass flats. In addition, since thick optical glass flats are used, the contrast ratio and switching speed of such an optical switch is not impaired.

Optical switch having spatial light modulators

A method for fabricating a high efficiency optical coupler by matching the emerging light exit pupil from a coupler opening to the acceptance shape of a couple optical fiber. An excimer laser forms the coupler opening in an optical fiber by removing cladding from the optical core surface. The coupler opening has an elliptical shape resulting in an emerging light exit cone, and that exit cone matches an acceptance cone of a circular coupler optical fiber.

Apparatus for fabrication of optical couplers

A method for fabricating optical components in the cladding of an optical fiber bus by the utilization of a laser. An excimer laser fabricates either an optical coupler opening or an optical mode scrambler by ablatively removing the cladding from the optical core of an optical fiber bus without damaging the optical core. Either coupler housing or a mode scrambler housing is attached to the optical fiber bus where the coupler or mode scrambler is to be fabricated. The coupler housing is used to position the laser, secure and align a coupler fiber, and provide cavities for junction and cladding repair materials. The mode scrambler housing serves a similar purpose.

Fabrication of optical components utilizing a laser

A cladding portion (15) of an optical fiber (16) is laser machined by focusing a laser beam (13) that is of an appropriate wavelength to ablate the cladding. When the laser beam completely penetrates through the cladding (15) to impinge on the optical fiber core (18) light is transmitted to the two ends of the fiber. A photodetector (31) is placed in close proximity to one of the ends of the optical fiber (16) with the photodetector output being connected to a laser control device (23). When the light detected by the detector exceeds a threshold, it generates a signal that stops the laser. Even if the cladding is of an unpredicted thickness, the laser beam is not terminated until there has been complete penetration through the cladding, and after complete ablation the laser beam is promptly terminated so as to avoid subsequent damage to the optical fiber.

Methods and apparatus for making optical fiber couplers

A conductive interconnection (27) on a substrate (11) is made by applying a metal-organic compound (25) to the substrate, exposing the metal-organic compound to laser beam radiation (14) in which the power level has been ramped to some specific level and, thereafter, moving the substrate with respect to the laser beam. The movement of the substrate is at an applied rate of speed such that the temperature within the metal-organic compound impinged by the laser beam is properly ramped with respect to time. This leaves a dependable metal deposition (27) which may be monitored through a viewing system (21).

Electrical conductor deposition method

A method for fabricating a high efficiency optical coupler by matching the emerging light exit pupil from a coupler opening to the acceptance shape of a coupler optical fiber. An excimer laser forms the coupler opening in an optical fiber by removing cladding from the optical core surface. The coupler opening has an elliptical shape resulting in an emerging light exit cone and that exit cone matches an acceptance cone of a circular coupler optical fiber.

Fabrication of optical couplers

An apparatus for fabricating optical fiber mode scramblers and optical fiber couplers as an integral part of an optical bus by the utilization of a laser to remove cladding on the optical fiber bus to form the mode scramblers and couplers. An excimer laser is utilized to ablatively remove the cladding which is a polymer material. The optical core is composed of a material which is not readily affected by the excimer laser. The optical bus is fabricated by enclosing an optical fiber in an optical bus assembly. The optical fiber has only cladding and an optical core and has no buffer surrounding the cladding. The optical bus assembly provides for a plurality of optical couplers for removing and adding light to the optical bus and intermixed with the optical coupler are a plurality of optical scramblers.

Fabrication of an integrated optical fiber bus

An excimer laser fabricates either an optical coupler opening or an optical mode scrambler by ablatively removing the cladding from the optical core of an optical fiber bus without damaging the optical core. Either coupler housing or a mode scrambler housing is attached to the optical fiber bus where the coupler or mode scrambler is to be fabricated. The coupler housing is used to position the laser, secure and align a coupler fiber, and provide cavities for junction and cladding repair materials. The mode scrambler housing serves a similar purpose.

Growing community of inventors

Cranbury, NJ, United States of America

Anthony J Serafino