Lutron Technology Company LLC

Lutron Electronics Company, Inc.

Andrew Karl Cooney

Justin J Mierta

Robert Charles Newman

David A Kirby

Edward J Blair

Stephen Lundy

Jason O Adams

Peter W Ogden, Jr

Chen Ming Wu

Justin M Zernhelt

Soumya Jain

Daniel W Mistarz

Jonathan L Roe

Galen Edgar Knode

Samuel F Chambers

Donald R Mosebrook

Jordan H Crafts

Jonathan T Lenz

Stuart W Dejonge

Alexander S Petersen

Robert C Newman

Devin N Malanaphy

Matthew J Price

Derek Thrasher

Jessica Bardio

Scott E Shaw

John T Lenz

Edwards J Blair

A low-power radio-frequency (RF) receiver is characterized by a decreased current consumption over prior art RF receivers, such that the RF receiver may be used in control devices, such as battery-powered motorized window treatments and two-wire dimmer switches. The RF receiver uses an RF sub-sampling technique to check for the RF signals and then put the RF receiver to sleep for a sleep time that is longer than a packet length of a transmitted packet to thus conserve battery power and lengthen the lifetime of the batteries. The RF receiver compares detected RF energy to a detect threshold that may be increased to decrease the sensitivity of the RF receiver and increase the lifetime of the batteries. After detecting that an RF signal is being transmitted, the RF receiver is put to sleep for a snooze time period that is longer than the sleep time and just slightly shorter than the time between two consecutive transmitted packets to further conserve battery power.

Low-power radio-frequency receiver

A control device may include a processor may include a core, a timer peripheral, and a peripheral direct memory access controller. The processor may include a receive port coupled to a communication port of the reporting device via a communication line. The control device may include a timer peripheral that can generate an enable signal and a timing signal, and a buffer circuit that may include an enable port for the enable signal for enabling/disabling the buffer circuit, an input port for the timing signal, and an output port coupled to the communication line. The processor may enable/disable the buffer circuit to control the timing of data bit(s) transmission across the communication line by the reporting device. The peripheral direct memory access controller may store the data bit(s) in a receive buffer during the bit period, and the core may subsequently retrieve the data bit(s) from the receiver buffer.

Method for communication between components of an electrical device

A control module may control a control device of a load control system. The control module may include a connector that can be coupled to the control device for receiving power and communicating with the control device. The control module may include a first wired communication circuit may be coupled to the third and fourth electrical terminals and configured to communicate with the control device when the control module is coupled to the control device using a four-wire topology. The control module may include a second wired communication circuit may be coupled to the first and second electrical terminals and configured to communicate with the control device when the control module is coupled to the control device using a two-wire topology. The control circuit may be configured to determine whether to communicate with the control device using the first wired communication circuit or the second wired communication circuit.

Automatic configuration of a control module for a lighting fixture

A motorized window treatment may provide a low-cost solution for controlling the amount of daylight entering a space through a window. The window treatment may include a covering material (e.g., a cellular shade fabric or a roller shade fabric), a drive assembly for raising and lowering the covering material, and a motor drive unit including a motor configured to drive the drive assembly to raise and lower the covering material. The motorized window treatment may comprise one or more battery packs configured to receive batteries for powering the motor drive unit. The batteries may be located out of view of a user of the motorized window treatment (e.g., in a headrail or in a battery compartment). The motorized window treatment may use various power-saving methods to lengthen the lifetime of the batteries, e.g., to reduce the motor speed to conserve additional battery power and extend the lifetime of the batteries.

Motorized window treatment

A motorized window treatment for controlling the amount of daylight entering a space through a window includes a covering material, a drive shaft, and a motor coupled to the drive shaft for raising and lowering the covering material. The window treatment also includes a spring assist unit for assisting the motor by providing a torque that equals the torque provided by the weight on the cords that lift the covering material at a position midway between fully-open and fully-closed positions to minimize motor usage and conserve battery life. The window treatment may comprise a photosensor for measuring the amount of daylight outside the window and temperature sensors for measuring the temperatures inside and outside of the window. The position of the covering material may be automatically controlled in response to the photosensor and the temperature sensors, or in response to an infrared or radio-frequency remote control.

A motorized window treatment provides a low-cost solution for controlling the amount of daylight entering a space through a window. The window treatment includes a covering material, a drive shaft, at least one lift cord rotatably received around the drive shaft and connected to the covering material, and a motor coupled to the drive shaft for raising and lowering the covering material. The window treatment also includes a spring assist unit for assisting the motor by providing a torque that equals the torque provided by the weight on the cords that lift the covering material at a position midway between fully-open and fully-closed positions, which helps to minimize motor usage and conserve battery life if a battery is used to power the motorized window treatment. The window treatment may comprise a photosensor for measuring the amount of daylight outside the window and temperature sensors for measuring the temperatures inside and outside of the window. The position of the covering material may be automatically controlled in response to the photosensor and the temperature sensors to save energy, or may also be controlled in response to an infrared or radio-frequency remote control.

A low-power RF receiver has a decreased current consumption. The receiver may be used in control devices, such as battery-powered motorized window treatments and two-wire dimmer switches. The receiver uses an RF sub-sampling technique to check for RF signals and then puts the receiver to sleep for a sleep time that is longer than a packet length of a transmitted packet to conserve battery power. The receiver compares detected RF energy to a threshold that may be increased to decrease the sensitivity of the receiver and increase the battery lifetime. After detecting an RF signal, the receiver is put to sleep for a snooze time that is longer than the sleep time and just slightly shorter than the time between two consecutive transmitted packets.

A motorized window treatment controls daylight entering a space through a window and includes a covering material, a drive shaft, lift cords received around the drive shaft and connected to the covering material, and a motor coupled to the drive shaft. It also includes a spring assist unit for the motor providing a torque that equals the torque provided by the weight on the lift cords at a position midway between fully-open and fully-closed positions, minimizing motor usage and conserving battery life. A photosensor for measuring the daylight outside the window and temperature sensors for measuring the temperatures inside and outside of the window may be provided. The position of the covering material is automatically controlled to save energy, or may also be controlled in response to an infrared or radio-frequency remote control.

Growing community of inventors

Quakertown, PA, United States of America

Andrew Karl Cooney