Amazon Technologies, Inc.

Akshay Mohan

Jagan Vaidyanathan Rajagopalan

Deepak Pai Hosadurga

Mudit Sunilkumar Khasgiwala

Duck Ho Bae

Yue Zheng

Nathan Labadie

Rohit Sammeta

Khaled Ahmad Obeidat

Hariharan Muthukrishnan

Ze Sun

Chunyu Wu

A wireless device may use two communication interfaces that utilize frequencies within the same band. As a result, a first communication interface such as an HDMI interface may interfere with operation of a second communication interface such as a WiFi interface. A conductive member is placed between the communication interfaces to reduce this interference. The conductive member has multiple slots, each slot having dimensions that cause resonance at a frequency used by the first communication interface. The number and spacing of the slots corresponds to the strength of signals used by the second communication interface. Placement of the conductive member between the first and second communication interfaces enables the conductive member to attenuate signals from the second communication interface that would interfere with the frequency used by the first communication interface.

Patterned housing element to reduce interference

A device such as an autonomous mobile device may include an extensible mast or other structure that changes length during operation. A cable between electronics at the ends of the structure includes a data line for signals and a power line for electrical power. A deployed length of the cable is determined and used to determine the phase of an antinoise signal that is radiated using the power line. The antinoise signal destructively interferes with at least a portion of the radiated noise from the data line, reducing the overall amplitude of the radiated noise. The deployed length may also be used to adjust other parameters, such as equalizer settings for one or more of a transmitter or receiver that is connected to the data line.

Electromagnetic noise cancellation apparatus for cable deployed at varying length

Technologies for dynamic noise cancelation using noise patterns are described. One device includes a moveable assembly having first and second degrees of freedom. A component within the base assembly radiates electromagnetic energy in a radiation pattern as a noise source when operating and an antenna, coupled to a receiver, is disposed on the support member. The processing device, using noise profile data about the radiation pattern of the noise source, determines that the component is operating and a current angle between the component and the antenna. The processing device determines a difference value between the current angle and the first angle and causes the moveable assembly to move at least one of the antenna or the base assembly according to the difference value.

Dynamic noise cancellation using noise patterns

High-speed data connectors having a variety of different implementations to address unwanted electromagnetic radiation and interference are described. In some instances, resonant unit structures are added within the existing connector cavity that absorb and dampen unwanted electromagnetic radiation. In other instances, resonant unit structures are added to the exterior of the connector to reduce and eliminate surface currents that can occur on the solid metal shield of the connector. In these and other instances, the resonant unit structure can be formed from a stacked structure having a resonant structure arranged in close proximity to some of the connector pins to absorb unwanted radiation from those pins. The absorbed energy is transferred to ground through other components in the stack. In still other instances, various different materials are provided to replace the conventional plastic material that is used to keep the connector pins in place and in alignment. The different materials can absorb unwanted electromagnetic radiation, and can be selected to address particular frequency ranges.

Low noise high-speed data connectors

An apparatus includes a circuit board including a contact pad. The circuit board includes one or more chips on the circuit board. The circuit board further includes a signal pin having a first end, a second end, and an intermediate portion between the first end and the second end. The first end of the signal pin is in contact with the contact pad, where the signal pin has a resonant frequency outside a predetermined frequency range. The apparatus includes a lossy dielectric material surrounding the intermediate portion of the signal pin, where the lossy dielectric material is configured to absorb radio frequency signals from the signal pin in the predetermined frequency range.

Device connector with reduced electromagnetic noise

A device is described. The device includes a data interface connector, an application processor, and interface circuitry. The application processor can receive signals via an antenna. The interface circuitry can be coupled between the application processor and the data interface connector. The data interface circuitry can determine a change in a signal property of one of the signals, the change being caused by an impedance mismatch between the data interface connector and a media consumption device. The data interface circuitry can also send the application processor a signal property setting corresponding with the change. The application processor can adjust the signal property of a subsequent one of the signals, in response to the signal property setting from the interface circuitry, to obtain an adjusted signal. The application processor can also send the adjusted signal to the media consumption device.

Adaptive impedance matching interface

A processing device detects an occurrence of the first set of use conditions associated with a power supply line coupled between a power source and a power sink in a user device. The processing device sets a tunable decoupling capacitor on the power supply line to a first capacitance value to reduce a level of electromagnetic interference on the power supply line at a first frequency corresponding to the first capacitance value. When the processing device detects a change from the first set of use conditions associated with the power supply line to a second set of use conditions, the processing device sets the tunable decoupling capacitor to a second capacitance value to reduce a level of electromagnetic interference on the power supply line at a second frequency corresponding to the second capacitance value.

Growing community of inventors

San Jose, CA, United States of America

Akshay Mohan