Elenion Technologies, LLC

Nokia Solutions and Networks Oy

Abdelrahman Ahmed

Alexander V Rylyakov

Ariel Leonardo Vera Villarroel

Richard C Younce

Yang Liu

Ran Ding

Mostafa Ahmed

Christopher Williams

Ruizhi Shi

Daihyun Lim

A multi-section optical modulator and related method are disclosed wherein two waveguide arms traverse a plurality of successive modulating sections. A differential drive signal is applied separately to each waveguide arm of each modulating sections in synchronism with the transmission of light along the waveguide arms, effecting a dual differential driving of each section. By suitably selecting the number of modulating sections and the section length, a high modulation bandwidth and a high modulation efficiency may be achieved simultaneously for a given peak-to-peak voltage swing of the drive signal.

Optical waveguide modulator

In optical receivers, extending the transimpedance amplifier's (TIA) dynamic range is a key to increasing the receiver's dynamic range, and therefore increase the channel capacity. Ideally, the TIA requires controllable gain, whereby the receiver can modify the characteristics of the TIA and/or the VGA to process high power incoming signals with a defined maximum distortion, and low power incoming signals with a defined maximum noise. A solution to the problem is to provide TIA's with reconfigurable feedback resistors, which are adjustable based on the level of power, e.g. current, generated by the photodetector, and variable load resistors, which are adjustable based on the change in impedance caused by the change in the feedback resistor.

Reconfigurable optical receivers for extended maximum input signals

A multi-section optical modulator and related method are disclosed wherein two waveguide arms traverse a plurality of successive modulating sections. A differential drive signal is applied separately to each waveguide arm of each modulating sections in synchronism with the transmission of light along the waveguide arms, affecting a dual differential driving of each section. By suitably selecting the number of modulating sections and the section length, a high modulation bandwidth and a high modulation efficiency may be achieved simultaneously for a given peak-to-peak voltage swing of the drive signal.

Within a modulator driver, different blocks are employed, e.g. a buffer, one or more variable gain amplifiers (VGA), and a final driver stage. Each of these blocks has an optimum bias point for best performance; however, interconnecting the blocks requires sharing the DC bias points in their interface, which does not necessarily match the optimum performance bias point of each block. Accordingly, a first offset feedback loop extending from reference points after a selected one of the blocks to an input of one of the blocks. The first offset feedback loop includes current sources capable of delivering a variable current to the input of the selected block in order to compensate any offset in an amplified differential input electrical signal measured at the reference points. A first bias feedback loop is also provided, including a current sinker for subtracting excess current introduced in the first offset compensation feedback loop.

Dual loop bias circuit with offset compensation

In optical receivers, extending the transimpedance amplifier's (TIA) dynamic range is a key to increasing the receiver's dynamic range, and therefore increase the channel capacity. Ideally, the TIA requires controllable gain, whereby the receiver can modify the characteristics of the TIA and/or the VGA to process high power incoming signals with a defined maximum distortion, and low power incoming signals with a defined maximum noise. A solution to the problem is to provide TIA's and VGA's with reconfigurable sizes, which are adjustable based on the level of power, e.g. current, generated by the photodetector.

Reconfigurable optical receivers with extended dynamic range

In optical receivers, cancelling the DC component of the incoming current is a key to increasing the receiver's effectiveness, and therefore increase the channel capacity. Ideally, the receiver includes a DC cancellation circuit for removing the DC component; however, in differential receivers an offset may be created between the output voltage components caused by the various amplifiers. Accordingly, an offset cancellation circuit is required to determine the offset and to modify the DC cancellation circuit accordingly.

Optical receivers with DC cancellation bias circuit and embedded offset cancellation

An optical coherent receiver includes an optical hybrid (OH) configured to mix signal and reference light, and two back-end optical ports. An optical equalizing network interconnects two 180&#xb0; OH output ports with the two back-end optical ports so that each back-end optical port receives light from each of the two OH output ports. Optical signals from each of the two back-end optical ports are converted to electrical signals that are fed to a differential amplifier. Adjusting coupling ratios and/or optical delays in the optical equalizing network reduces an OSNR penalty of a lower-bandwidth differential amplifier.

Optical domain equalization for coherent optical receivers

A multi-section optical modulator and related method wherein two waveguide arms traverse a plurality of successive modulating sections. A differential drive signal is applied separately to each waveguide arm of each modulating sections in synchronism with the transmission of light along the waveguide arms, effecting a dual differential driving of each section. By suitably selecting the number of modulating sections and the section length, a high modulation bandwidth and a high modulation efficiency may be achieved simultaneously for a given peak-to-peak voltage swing of the drive signal.

Growing community of inventors

Brooklyn, NY, United States of America

Abdelrahman Ahmed